|
|
03-12-2013, 08:14 PM
|
#81
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by gbaglo
So, I assume, that I can assume that if the trailer is level when I weigh the tongue, that it will still be level and weigh the same when the WDH is deployed.
|
Yes. The WDH doesn't change the tongue weight, and the as-towed configuration is level so a weight when level is the as-towed weight.
|
|
|
03-12-2013, 08:20 PM
|
#82
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by Floating Cloud
To me, the difference between a double and single is that when the tongue is parallel to the ground and then is lowered, I expect the weight to be greater. I understand that it is greater for a single axle. But it is less for double axles, at least that is the way I remember the weight going with our double axles. So apparently single and double axles do not act the same. If we put the tongue up, it becomes heavier, not lighter as expected.
|
Yes. That's what I tried to explain in post #49.
|
|
|
03-12-2013, 08:24 PM
|
#83
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
As an aside, I think it's interesting that Glenn is using a hydraulic jack to support a hydraulic scale. Plug that scale's pressure gauge into the jack, ditch the scale, and you would have the same measurement by the same method (although a calibration multiplier would be needed).
Just one of those things that amuse technical minds...
|
|
|
03-12-2013, 08:26 PM
|
#84
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by gbaglo
Well, those with 19s could simply remove one of the wheels on each side, preferably the ones furthest from the centre, prior to weighing.
|
Kidding, right? It can be hard to tell with some people...
|
|
|
03-12-2013, 08:41 PM
|
#85
|
Senior Member
Join Date: Nov 2010
Location: Denison, Texas
Trailer: 2015 21'; 2011 19' sold; 4Runner; ph ninezero3 327-27ninefour
Posts: 5,136
|
Quote:
Originally Posted by Brian B-P
Yes. That's what I tried to explain in post #49.
|
Good, I'm glad you have said the same in another way as it always seems strange that it occurs.
__________________
Cathy. Floating Cloud
"Live in the sunshine, swim the sea, drink the wild air.... "
Emerson
|
|
|
03-12-2013, 08:42 PM
|
#86
|
Senior Member
Join Date: Nov 2010
Location: Denison, Texas
Trailer: 2015 21'; 2011 19' sold; 4Runner; ph ninezero3 327-27ninefour
Posts: 5,136
|
[QUOTE=Brian B-P;23577]Kidding, right? It can be hard to tell with some people...[/
We were just taking those pesky wheels off the other day....
__________________
Cathy. Floating Cloud
"Live in the sunshine, swim the sea, drink the wild air.... "
Emerson
|
|
|
03-12-2013, 09:55 PM
|
#87
|
Senior Member
Join Date: Aug 2012
Location: Portland, Oregon
Trailer: 2002 Escape 13'
Posts: 967
|
I just had to chime in because the absurdity of this thread is classic!
We seem to have a awful lot of passion and time for this subject. Are you all snowed in or what?
|
|
|
03-12-2013, 10:31 PM
|
#88
|
Member
Join Date: Dec 2012
Location: Vancouver, British Columbia
Trailer: 2010 Escape 15B (c)
Posts: 66
|
No Hotfishtacos, it rained yesterday, today and is forecast for the next three days. Re #49. I stopped reading when it was said that raising the tongue changed the tongue weight. I figured that would only happen if the wheels were chocked and couldnt move. I thought that, in order for the tongue to be raised vertically the wheels would have to be free to move slightly in reverse which would result in no weight movement. This took into account that the driveway sloped toward the road and you backed the trailer in. Of course I was thinking of a single axle unit. Maybe I read things differently. Cheers, Richard
__________________
2010 Escape 15B (c) pulled by a 2006 Jeep Liberty Sport
"It's quicker to go slow" &
"You're only young once, you're a helluva long time dead"
|
|
|
03-12-2013, 11:13 PM
|
#89
|
Senior Member
Join Date: Oct 2008
Location: North Vancouver, British Columbia
Trailer: 2009 Escape 17B 2020 Toyota Highlander XLE
Posts: 17,136
|
Back at post #17 I said I was weighing a single axle 17' trailer.
All the posts following, I have attempted to explain that I was weighing a single axle trailer.
And then the wheels fell off.
__________________
What happens to the hole when the cheese is gone?
- Bertolt Brecht
|
|
|
03-12-2013, 11:16 PM
|
#90
|
Member
Join Date: Dec 2012
Location: Vancouver, British Columbia
Trailer: 2010 Escape 15B (c)
Posts: 66
|
Naw everyone got their tongues twisted!. Cheers, Richard
__________________
2010 Escape 15B (c) pulled by a 2006 Jeep Liberty Sport
"It's quicker to go slow" &
"You're only young once, you're a helluva long time dead"
|
|
|
03-13-2013, 12:02 AM
|
#91
|
Senior Member
Join Date: Jan 2012
Location: Vancouver, British Columbia
Trailer: 2012 15A
Posts: 398
|
Quote:
Originally Posted by Dixhiccup
No Hotfishtacos, it rained yesterday, today and is forecast for the next three days. Re #49. I stopped reading when it was said that raising the tongue changed the tongue weight. I figured that would only happen if the wheels were chocked and couldnt move. I thought that, in order for the tongue to be raised vertically the wheels would have to be free to move slightly in reverse which would result in no weight movement. This took into account that the driveway sloped toward the road and you backed the trailer in. Of course I was thinking of a single axle unit. Maybe I read things differently. Cheers, Richard
|
One of the critical factors in the analysis is the location of the Centre of Gravity (C of G) of the trailer. The higher it is above the frame the greater the effect towing above or below level will have (statics 101 analysis).
When you tow a trailer tilted up from level the C of G effective horizontal distance moves slightly back towards the axle and results in a decrease in tongue weight from that at level trailer. Tilt the tongue below level and the C of G distance effectively moves forward and increases the tongue weight while towing in the that position.
Think of a loaded wheel barrow which is most like a single axle trailer setup. Picture the C of G being centered between the wheel axle and the handles and 2 ft above the handles then lift and lower the handles above level and see what happens to its horizontal location relative to the axle. In the worst case if you rotated upwards 90 deg the weight on the handles would be zero. Rotate 90 deg down and the total weight would be on the handles.
I agree with those who have stated that a single axle trailer, level, on sloping ground will give the same tongue weight as towing a level trailer, on level ground. The ground slope has no effect on vertical forces or vertical reactions. The chocks and friction resist any horizontal forces, due to slope, and you only have the vertical forces left, as Jim B stated, and you then measure only vertical tongue weight in a level position - the desired outcome if you tow level.
Towing up or down a hill is another analysis, although similar, from determining tongue weight with a level trailer. Once again it is the C of G that accounts for the weight shift. Your level trailer is still parallel to the road but the whole setup is on a slope and the effective horizontal distance to the C of G has again changed.
So pack your heavy stuff on the floor and light stuff up high to keep the C of G as low as possible. If all the mass of a trailer were only in the frame then the tilt effect would be very minimal.
That is my 5 cents worth that I had to get in before they take our nickel away as well.
Now back to the squeegee for me to get the rain off the deck!!!
Can't wait for it to warm up and the sun to come out so we can get out there and camp in t-shirts and shorts. Figure that one out, eh!
|
|
|
03-13-2013, 12:32 AM
|
#92
|
Senior Member
Join Date: Oct 2008
Location: North Vancouver, British Columbia
Trailer: 2009 Escape 17B 2020 Toyota Highlander XLE
Posts: 17,136
|
All that, and thank you, explains why when I was moving a 400 lb. boulder on a dolly, and the C of G shifted, that I got fired over the dolly handles and into the fence on the other side.
No damage to me, fortunately, and I decided that the placement of the boulder in my rock garden was just perfect.
There is always a solution.
__________________
What happens to the hole when the cheese is gone?
- Bertolt Brecht
|
|
|
03-13-2013, 12:36 AM
|
#93
|
Member
Join Date: Dec 2012
Location: Vancouver, British Columbia
Trailer: 2010 Escape 15B (c)
Posts: 66
|
I'm out of this. It seems to me that Baglo stated early on I.e #17 that his is a 17 single axle & the next ten or fifteen posts went slightly off track or agreed with him. He stated he had used blocks to get his 17 level and then raised the tongue about 1/4" so there couldn't have been any appreciable change in tongue weight or c of g. Thereafter things seem to go off the rails and it became very confusing with all the different views of the apparent problems. Glen I just read my next post, seems you had someone on your side. Now I'm going to put my grand daughters engine back in her toy box. Cheers, Richard
__________________
2010 Escape 15B (c) pulled by a 2006 Jeep Liberty Sport
"It's quicker to go slow" &
"You're only young once, you're a helluva long time dead"
|
|
|
03-13-2013, 12:45 AM
|
#94
|
Senior Member
Join Date: Oct 2008
Location: North Vancouver, British Columbia
Trailer: 2009 Escape 17B 2020 Toyota Highlander XLE
Posts: 17,136
|
Nothing left on the bone.
__________________
What happens to the hole when the cheese is gone?
- Bertolt Brecht
|
|
|
03-13-2013, 01:03 AM
|
#95
|
Senior Member
Join Date: Jan 2012
Location: Vancouver, British Columbia
Trailer: 2012 15A
Posts: 398
|
Here is an example.
Trailer: 15’ Escape, total mass 2500 lbs. loaded
Tongue weight: 300 lbs. or 12%, level trailer
Assume C of G is 3 feet above frame, vertical distance.
Distance from axle to hitch: 10 ft. as measured
Assume axle and hitch are on the same plane and no friction in system
Calculated C of G: 1.20 ft. ahead of axle, horizontal distance
Assume hitch point is 3 inches above level.
Trailer slope = 1.4321 deg. or 2.5%
Calculated new horizontal location of C of G is 1.1246 ft. (shift 0.0754 ft. or 0.9 inches back)
Calculated tongue wt. tilted = 281.2 lbs. or 11.25% of trailer mass (18.8 lbs. less)
The values for a 17 ft. trailer would be nearly the same based on same weights and a 2 foot longer distance from axle to hitch and new horizontal C of G calculated.
The tongue weight value for 3 inches lower would be 318.7 lbs or 12.75% of trailer mass.
3 inches above or below level is a lot I believe, with small change in tongue weight? Problem
Please comment if you agree or do not agree with my static calculations.
Has anyone actually measured tongue weights to compared level vs. sloped?
I know Glen would love to go out and do it but he is probably tired of setting up and there is more rain in the forecast! Time for an Okanagan Spring, beer eh.
|
|
|
03-13-2013, 01:05 AM
|
#96
|
Senior Member
Join Date: Feb 2013
Location: Surrey, British Columbia
Trailer: 2014 Escape 19'
Posts: 264
|
I have been following this forum for a month or so, and decided to jump in on this thread with my two bits (skipping from pennies, right past nickels and dimes). The forces and weight distribution on the wheel may differ depending on the slope of the surface, and also the addition of wheel chocks and blocks. However the weight transfer from the wheel to axle and axle to trailer frame should not vary because of the slope of the surfaces supporting the wheel. So, the remaining trailer weight (the tongue weight), also will be constant, whether it is supported on a pedestal the same height as the trailer wheel or not.
Now, if the scale measuring the tongue weight is not vertical (if it is not sitting on a level surface), then the scale will not show an accurate measurement - it will be measuring diagonal forces. Here is something else for all of us closet physicists to consider.
Baglo's tongue scale set up appears to be on the level, so should be accurate.
|
|
|
03-13-2013, 01:08 AM
|
#97
|
Senior Member
Join Date: Oct 2008
Location: North Vancouver, British Columbia
Trailer: 2009 Escape 17B 2020 Toyota Highlander XLE
Posts: 17,136
|
I have a solution ... of water, malt, sugar and hops. Oh ya, yeast.
__________________
What happens to the hole when the cheese is gone?
- Bertolt Brecht
|
|
|
03-13-2013, 01:18 PM
|
#98
|
Senior Member
Join Date: Jan 2012
Location: Vancouver, British Columbia
Trailer: 2012 15A
Posts: 398
|
Quote:
Originally Posted by gbaglo
Nothing left on the bone.
|
Hopefully it will not be a three dog night on top of the rain.
|
|
|
03-13-2013, 03:43 PM
|
#99
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by JohnB
...Assume C of G is 3 feet above frame, vertical distance
...
Assume hitch point is 3 inches above level.
Trailer slope = 1.4321 deg. or 2.5%
Calculated new horizontal location of C of G is 1.1246 ft. (shift 0.0754 ft. or 0.9 inches back)
Calculated tongue wt. tilted = 281.2 lbs. or 11.25% of trailer mass (18.8 lbs. less)
|
Since the single-axle trailer is sitting on a wheel which rotates on a hub when the trailer is tilted (not a leg extending to the ground at the tire contact point, and nothing to do with the frame height), I believe that the relevant height for the shift calculation is the height of the C of G above the axle, not above the ground or the frame. If the C of G were right at the axle height the shift with small angle change would be entirely vertical - no horizontal shift or tongue weight change at all. Although the real C of G is well above the axle, this still means that the effect is small - I don't think it's a big deal for single-axle trailers of a reasonable height.
I did check this experimentally with my single-axle Boler and a scale; unfortunately it was years ago and I do not recall the numbers.
I checked with a tandem-axle cargo trailer that I had rented, and the larger (and opposite direction) load shift for even 2 inches of hitch height change was significant.
Quote:
Originally Posted by KirkB
The forces and weight distribution on the wheel may differ depending on the slope of the surface, and also the addition of wheel chocks and blocks. However the weight transfer from the wheel to axle and axle to trailer frame should not vary because of the slope of the surfaces supporting the wheel. So, the remaining trailer weight (the tongue weight), also will be constant, whether it is supported on a pedestal the same height as the trailer wheel or not.
Now, if the scale measuring the tongue weight is not vertical (if it is not sitting on a level surface), then the scale will not show an accurate measurement - it will be measuring diagonal forces. Here is something else for all of us closet physicists to consider.
Baglo's tongue scale set up appears to be on the level, so should be accurate.
|
I agree with all of this! Despite all the flak we have given him for complicating things, in his situation it is perfectly valid to prop up the tongue to get a correct tongue weight measurement and confirm appropriate loading before a trip.
|
|
|
03-13-2013, 11:14 PM
|
#100
|
Senior Member
Join Date: Nov 2010
Location: Denison, Texas
Trailer: 2015 21'; 2011 19' sold; 4Runner; ph ninezero3 327-27ninefour
Posts: 5,136
|
What are we going to do without Toad On A Slope to talk about? Sounds like a drink. I'll have to come up with some concoction!
I appreciate Doug having started the thread and Glenn's question as such threads are always a learning experience or at least a little refresher course for the experts. We do not, however, have any real world examples with numbers. That would be good to get. I have never seen an instruction to get tongue weight except on a level surface but I guess I want to include slopes now!
I still suggest what I always suggest in such a case, namely, that a person becomes familiar with his own situation by doing the numbers. It is rare that scientific or engineering claims can be checked but TWs can be done easily. We apparently do still have some unresolved points. Might as well check on them to make sure.
__________________
Cathy. Floating Cloud
"Live in the sunshine, swim the sea, drink the wild air.... "
Emerson
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|