|
|
11-09-2018, 02:20 PM
|
#121
|
Senior Member
Join Date: Aug 2016
Location: Bozeman, Montana
Trailer: 2018 5.0TA / 2018 GMC Canyon/Duramax
Posts: 561
|
Quote:
Originally Posted by Ronn
Hi Kent, we are in the process of doing our build sheet and being you have now lived with your dinette decision I am wondering if you would share your thoughts. We also plan on the U shaped dinette, the Lagun table mount and looking to widen the back bench 5". How has this worked out for you and any other thoughts, suggestions would be appreciated.
Thanks, Ronn
|
Ronn, no regrets with my decision. When I was working with Tina and received the approval. I went back and forth between adding 4 or 5 inches and decided on additional 4 inches, but would not add more then 5 inches. Stock depth is 18 inches from back wall.
Having the extra inches makes the rear bench more usable and a side benefit is extra space below the bench for Lagun back mount and if you plan on adding solar and or other electrical parts and pieces. Even with this change you can sit up to 4 people if needed, 3 comfortable and two very comfortable. Wished ETI used thicker or firmer foam for the cushions.
I also opted for 4 inch back cushion across the back and glad I did.
Besides the faucet issue talked about on other thread, one thing I would do differently.
Instead of having them put shower diverter center of wall I would have them put in corner were sink would go. Having faucet on center of wall is kind of in the way. Remember I opted for no bath sink. No regrets on not having bath sink. If you have bath sink, the faucet is mounted on sink in corner.
I'm in the process of changing the single handle Dura Faucet to two handle with tub diverter as I'm not happy with the single handle.
|
|
|
11-09-2018, 06:46 PM
|
#122
|
Senior Member
Join Date: Jul 2018
Location: Minneapolis, Minnesota
Trailer: 2019 5.0 TA
Posts: 864
|
Quote:
Originally Posted by Kent
Ronn, no regrets with my decision. When I was working with Tina and received the approval. I went back and forth between adding 4 or 5 inches and decided on additional 4 inches, but would not add more then 5 inches. Stock depth is 18 inches from back wall.
It sounds as if you are happy that you went with a 4" wider bench even with the wider 'back' cushion? We went back and forth between 4 to 6 inches and settled for 5"
Having the extra inches makes the rear bench more usable and a side benefit is extra space below the bench for Lagun back mount and if you plan on adding solar and or other electrical parts and pieces.
good point as I could see on your Lagun mount the space looked tight
Even with this change you can sit up to 4 people if needed, 3 comfortable and two very comfortable.
Wished ETI used thicker or firmer foam for the cushions.
are you talking about the seat cushion or both the seat and back could be thicker/denser?
I also opted for 4 inch back cushion across the back and glad I did.
I did notice that the "back cushion" on the rear seat was much thinner but we didn't widen it, I am going to change that to 4"
Besides the faucet issue talked about on other thread, one thing I would do differently.
Instead of having them put shower diverter center of wall I would have them put in corner were sink would go. Having faucet on center of wall is kind of in the way. Remember I opted for no bath sink. No regrets on not having bath sink. If you have bath sink, the faucet is mounted on sink in corner.
we are keeping the bathroom faucet as is
I'm in the process of changing the single handle Dura Faucet to two handle with tub diverter as I'm not happy with the single handle.
|
Thanks
__________________
The Sweet Suite
Ronn and Colleen
|
|
|
11-09-2018, 06:53 PM
|
#123
|
Senior Member
Join Date: Aug 2016
Location: Bozeman, Montana
Trailer: 2018 5.0TA / 2018 GMC Canyon/Duramax
Posts: 561
|
Quote:
Originally Posted by Ronn
Thanks
|
Ronn, with regards to cushion thickness I would prefer firmer or thicker cushion for seats. I thick all seat back cushions should be firmer.
|
|
|
04-20-2019, 06:28 PM
|
#124
|
Senior Member
Join Date: Jul 2018
Location: Minneapolis, Minnesota
Trailer: 2019 5.0 TA
Posts: 864
|
Quote:
Originally Posted by Kent
Today I installed black Formica panels into refrigerator doors and started the Lagun table mount project.
The only thing remaining for the Lagun mount is to install the metal brace behind the wall, but that will have to wait until after Osoyoos.
It is pretty solid without the metal brace now as I mounted two ¾” plywood panels; one panel to fill the framing behind the bench foot board and the second larger panel to sandwich the inserted panel and the framing.
I also ran a strip of 3/4” angle aluminum across the top of bench as well.
|
Hi Kent, I am curious as to how you attached the first (of 2) plywood piece, I see that it looks like you screwed the second on into the first one. Thanks
__________________
The Sweet Suite
Ronn and Colleen
|
|
|
04-24-2019, 06:46 PM
|
#125
|
Senior Member
Join Date: Aug 2016
Location: Bozeman, Montana
Trailer: 2018 5.0TA / 2018 GMC Canyon/Duramax
Posts: 561
|
Quote:
Originally Posted by Ronn
Hi Kent, I am curious as to how you attached the first (of 2) plywood piece, I see that it looks like you screwed the second on into the first one. Thanks
|
Ronn, the first 3/4 inch plywood was cut to fit inside the existing framing and the second 3/4" piece was cut to overlape and screw to the framing, thus sandwiching the first piece.
The stock Lagun mount bolts were replaced with longer bolts and go through the stock factory foot-board, two 3/4" pieces of plywood and the metal reinforcing mount bolted to the floor under the bench.
At the time my local ACE hardware did not have count-sunk screws in the length I needed and ended up with a pan head style that fits inside the count-sink recess.
Very solid!
|
|
|
04-24-2019, 06:59 PM
|
#126
|
Senior Member
Join Date: Aug 2016
Location: Bozeman, Montana
Trailer: 2018 5.0TA / 2018 GMC Canyon/Duramax
Posts: 561
|
Quote:
Originally Posted by Ronn
Hi Kent, I am curious as to how you attached the first (of 2) plywood piece, I see that it looks like you screwed the second on into the first one. Thanks
|
Ronn, picture with bracket mounted.
|
|
|
04-24-2019, 08:38 PM
|
#127
|
Senior Member
Join Date: Jul 2018
Location: Minneapolis, Minnesota
Trailer: 2019 5.0 TA
Posts: 864
|
Quote:
Originally Posted by Kent
Ronn, the first 3/4 inch plywood was cut to fit inside the existing framing and the second 3/4" piece was cut to overlape and screw to the framing, thus sandwiching the first piece.
The stock Lagun mount bolts were replaced with longer bolts and go through the stock factory foot-board, two 3/4" pieces of plywood and the metal reinforcing mount bolted to the floor under the bench.
At the time my local ACE hardware did not have count-sunk screws in the length I needed and ended up with a pan head style that fits inside the count-sink recess.
Very solid!
|
Got it, great. Thank you
__________________
The Sweet Suite
Ronn and Colleen
|
|
|
04-25-2019, 07:01 AM
|
#128
|
Junior Member
Join Date: Apr 2019
Location: Where I park, Texas
Trailer: Winnebego Micro-Mini 2106 FBS
Posts: 20
|
Where are you taking it for it’s shakedown trip?
Congratulations!
__________________
“Oh, the places you'll go.”....Dr. Seuss
|
|
|
07-24-2019, 10:37 PM
|
#129
|
Senior Member
Join Date: Aug 2016
Location: Bozeman, Montana
Trailer: 2018 5.0TA / 2018 GMC Canyon/Duramax
Posts: 561
|
Tall Cabinet 5.0TA
As I use my 5.0TA I found I like using the tall cabinet on the passenger side to store non hanging clothes as it is easy access.
Sometime back I decided to put in shelves, but did not want anything permanent and finally came up with this.
The baskets work well for holding socks, shorts, pants etc.
Nothing is screwed into the existing cabinet and all can be removed returning the cabinet to original blank canvas.
Remaining items to finish is glue the front stops to the shelves and stain the shelves.
Once completed I will post pictures showing how I put this together for anyone interested.
|
|
|
05-25-2020, 08:23 PM
|
#130
|
Member
Join Date: Apr 2020
Location: Port Angeles, Washington
Trailer: 2021 5.0 TA in about a year. Lol
Posts: 77
|
Full Height Cabinet to Right of Entry Door, do you have a picture of that?
|
|
|
05-25-2020, 09:17 PM
|
#131
|
Senior Member
Join Date: Feb 2018
Location: Austin, Texas
Trailer: 2019 5.0TA "Junior", 2019 Ram 1500 5.7 Hemi
Posts: 1,600
|
Here you go....I added the interior shelves, it comes without them.
__________________
David, Mary, and the cats
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|