Will a 5.0 fit under a 9' or 10' garage door? - Page 3 - Escape Trailer Owners Community

Go Back   Escape Trailer Owners Community > Escape Me | General Topics > General Escape
Click Here to Login
Reply
 
Thread Tools Display Modes
 
Old 03-03-2014, 05:56 PM   #21
Site Team
 
Donna D.'s Avatar
 
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 6,830
The only time the water fill was a problem on my Scamp, it was caused by my young daughter. Scamps have a flip-up water fill on the back corner of the trailer for filling the fresh water tank. My child thought it was a great place for tiny pebbles and dirt to disappear. Kept her entertainment for quite some time. And folks question why deck plates are a good idea for cleaning out fresh water tanks.
__________________

Donna D. is offline   Reply With Quote
Old 03-03-2014, 06:12 PM   #22
Senior Member
 
Join Date: Dec 2011
Location: _, Texas
Trailer: Escape 5.0 SA
Posts: 545
Of coase I know the little plastic door & common CH751 lock are of no real security. I have something else for that. ETI must of thought it was worth something to install a locking door in production. From what was just posted, if your door gets broke off or the check valve fails now, we're going to have to search for some kind of replacement that fits the hole cut in the trailer. The classic first fiberglass trailers used open connections and fills. I don't care for retro or antiques. I was attracted to the 5.0 because it is sleek, innovative, and lightweight.
__________________

daveandsandyclink is offline   Reply With Quote
Old 03-03-2014, 07:35 PM   #23
Site Team
 
Donna D.'s Avatar
 
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 6,830
Quote:
Originally Posted by Brian B-P View Post
I would be more than a little nervous about the rectangular flat steel feet sitting well in dollies like that, and I (personally) would be much more confident about a properly fastened wheel, which would also be a much larger wheel than the little casters on those dollies.
I wouldn't worry in the least using the wheel dollies. Yes, they're made for tires, but you put the front end of the 5er down on those and the jacks aren't going to slide off of them, too much weight. The nice part is they barely skim the floor surface they way they're built. And the OP needs the front end low. Because they're casters, if you need to turn them at all, you can either aim the wheels in the direction you want to go before you put the lading gear down or even after. I've used them to turn a 1967 Mustang 90 degrees on an asphalt pad by myself. They work as designed.
Donna D. is offline   Reply With Quote
Old 03-03-2014, 10:50 PM   #24
Senior Member
 
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 9,055
It's good that the dollies work as designed for car tires, and should work here, but a jack wheel is actually designed for exactly this application. I guess there are a few options.
Brian B-P is offline   Reply With Quote
Old 03-03-2014, 11:06 PM   #25
Site Team
 
Donna D.'s Avatar
 
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 6,830
I think if ETI thought folks would use the landing gear on a 5er to move the trailer around, they'd either offer wheels as an option or not. I haven't seen wheels on the landing gear as an option. Most of the tubes on all jacks (seem to me) really lack in strength. The shorter the landing gear tube to wheel, the stronger it is. But, OMG... don't plan to extend the landing gear to its full length, put a wheel on the end and expect it to hold up while you shove the 5er around. That's a lot of weight. BUT, it's not my 5er. I know what I'm gonna do. Do you?
Donna D. is offline   Reply With Quote
Old 03-04-2014, 01:21 PM   #26
Senior Member
 
Join Date: Dec 2011
Location: _, Texas
Trailer: Escape 5.0 SA
Posts: 545
That's the point I was trying to make Donna. ETI moves 5.0s around the factory during production with wheels on the landing gear. But they don't have near the weight during that time. I purchased these wheels from ETI. They just slip on without any pins and that's why I welded longer, heaver pipe on them. When talking to Reace about this, he cautioned me about not being to rough or traveling to fast while moving it on the landing gear. That's not their intended use. Their just not that rigid and strong. As I stated...I go low and slow while pushing it about 30' on smooth, level concrete. I might add that you cannot see where your going and must have another person to guide you. It takes some effort to turn. If your reading this and planning to try it, be very carefull.
daveandsandyclink is offline   Reply With Quote
Old 03-04-2014, 01:35 PM   #27
Site Team
 
cpaharley2008's Avatar
 
Join Date: Jun 2010
Location: York, Pennsylvania
Trailer: 2016 2ndGen Escape 19' PRAIRIE SCHOONER pulled by 2014 Ram Hemi/8sp
Posts: 13,675
The other issue is the floor. I'm sure the interior cement floors inside ETI are a lot smoother and slicker than exterior concrete floors. They use a special machine for making those floors inside large warehouses smooth for ease of movement.
__________________
Jim
The two most important days in your life are the day you were born and the day you find out why………..Mark Twain
cpaharley2008 is offline   Reply With Quote
Old 03-04-2014, 02:05 PM   #28
Site Team
 
Donna D.'s Avatar
 
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 6,830
Quote:
Originally Posted by daveandsandyclink View Post
I might add that you cannot see where your going and must have another person to guide you. It takes some effort to turn. If your reading this and planning to try it, be very carefull.
Thanks for the warning. But no. I'm not going to do it. My 5er will be under a carport where the Scamp currently resides. It's 18'x25' I have to back in at a bit of an angle, but the tug is up to the task.
Donna D. is offline   Reply With Quote
Old 03-04-2014, 10:28 PM   #29
Senior Member
 
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 9,055
Quote:
Originally Posted by Donna D. View Post
I haven't seen wheels on the landing gear as an option.
Escape did offer wheels to another owner, as reported in the other linked thread and just discussed again. It is not a normal option, perhaps because it would not normally be of interest. There are lots of things which could be offered and are not; that does not in itself mean they would be unsuitable.

Quote:
Originally Posted by Donna D. View Post
OMG... don't plan to extend the landing gear to its full length, put a wheel on the end and expect it to hold up while you shove the 5er around.
Perhaps more importantly, the other linked thread was about moving the trailer around in general; the proposal in this one is to kneel the trailer and push it straight into the garage, so if the jacks are used for this purpose the legs would not be extended. I agree that the the lateral strength of the jack would be much more of a concern if extended.

Quote:
Originally Posted by Donna D. View Post
Most of the tubes on all jacks (seem to me) really lack in strength.
...
That's a lot of weight.
The load on each jack is not high compared to the single tongue jack on a heavy conventional trailer, so even extended the idea does not seem unreasonable to me. While kneeling, a tandem axle 5.0 will have even less load on the jacks than it would while level (in contrast, a single-axle classic 5.0 would have somewhat more load kneeled than level).

Finally, I note that various trailer owners in other forums have reported unfortunate incidents in which the trailer was accidentally towed with the jack partially extended, or over humps with it retracted, and it dragged on the ground. This could produce far higher lateral forces than hand-pushing the trailer, and yet the usual result seems to be bending the mounting plate of the jack, or grinding the foot or jack leg end off, rather than any damage to the extension mechanism. Mine was apparently dragged by the previous owner, so the leg end is damaged; however, the jack (the 1979 original) still works fine (lacking a foot, I put in on a block). These jacks are not very stable laterally (they wiggle), but they're pretty strong.
Brian B-P is offline   Reply With Quote
Old 03-04-2014, 10:31 PM   #30
Senior Member
 
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 9,055
Quote:
Originally Posted by daveandsandyclink View Post
I purchased these wheels from ETI. They just slip on without any pins...
Do you know if the jack leg ends are the common type which would accept a normal pinned-on wheel? The stock foot appears to be pinned on, and online descriptions consistently of feet and wheels describe all common brands as being 2" diameter (presumably the outside diameter of the jack leg end).
__________________

Brian B-P is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off






» Virginia Campgrounds

Reviews provided by



All times are GMT -5. The time now is 08:37 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 2012 Social Knowledge, LLC All Rights Reserved.