|
01-12-2015, 12:15 PM
|
#1
|
Senior Member
Join Date: Jun 2014
Location: Box Elder, South Dakota
Trailer: Bigfoot 25' 2018
Posts: 347
|
Dinette Edge Trim ?
There is a plastic trim covering the 1/8" plywood on the dinette seats of our 19. It is a C or U channel and slips over this thin plywood. The color matches the walls well.
Does anyone know where to buy some of this trim? Anything similar? How about a better name so I can do a more effective Internet search? Substitute?
I need it to trim out a new plywood insert at the very front of the dinette after raising the floor. The one that's between the benches on an angle front to back.
Thanks in advance.
__________________
Hugh Currin
2018 Bigfoot 25'
2018 RAM 2500 Diesel
|
|
|
01-12-2015, 01:15 PM
|
#2
|
Senior Member
Join Date: Jul 2014
Location: Tampa Bay Area, Florida
Trailer: 2015 Escape 5.0TA (Little Elsie) Extensively Personalized
Posts: 2,969
|
You might just call Escape and ask Reace. I'm sure he would sell you some or tell you where to get it.
__________________
What a long strange trip it’s been!
|
|
|
01-12-2015, 03:05 PM
|
#3
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
I had Reace bring a couple of piece to the rally in Osoyoos last year, it comes in 8' strips, they also cover the edges in the cubbies and I wanted to cover all the edges not just the bottom ones. I'm sure you can get some there this year if you ask him to bring some to the rally. It is "U" shaped and cut with scissors.
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
01-16-2015, 10:07 AM
|
#4
|
Senior Member
Join Date: Jun 2014
Location: Box Elder, South Dakota
Trailer: Bigfoot 25' 2018
Posts: 347
|
Thanks for the replies. It does makes sense to contact ETI for trim. We won't get to Osoyoos this year but might talk Reese and Tammy into bringing some to Bandon. Althernately, shipping can't be that expensive.
I found I can get by re-using trim for my temporary testing. If it all works out, I'll likely do the finish work this summer. When I figure it out I'll call ETI and see what we can arrange.
Again, thank you for the help.
__________________
Hugh Currin
2018 Bigfoot 25'
2018 RAM 2500 Diesel
|
|
|
01-16-2015, 11:11 AM
|
#5
|
Senior Member
Join Date: Oct 2012
Location: Longview, WA, Washington
Trailer: 2013 Escape 15B - 2014 Nissan Frontier SL
Posts: 854
|
Quote:
Originally Posted by currinh
Thanks for the replies. It does makes sense to contact ETI for trim. We won't get to Osoyoos this year but might talk Reese and Tammy into bringing some to Bandon. Althernately, shipping can't be that expensive.
I found I can get by re-using trim for my temporary testing. If it all works out, I'll likely do the finish work this summer. When I figure it out I'll call ETI and see what we can arrange.
Again, thank you for the help.
|
We can pick it up at Osooyoos and give to you at Bandon. Send me a PM and arrange details. Tim
__________________
Tim and Julie
2013 Escape 15B
2014 Nissan Frontier, Previous 2012 Santa Fe
|
|
|
01-16-2015, 11:15 AM
|
#6
|
Senior Member
Join Date: Apr 2012
Location: Edmonton, Alberta
Trailer: 2013 19' & 2013 15B
Posts: 2,636
|
I would not bother with having anything shipped from ETI. This is a super common product. Just do a google search for "plastic t-moulding table edging". There has got to be numerous suppliers in your area who would be able to provide the same or a comparable product.
__________________
2013 19' \ 2013 15B, 2020 Toyota 4Runner TRD Offroad
"It is better to remain silent at the risk of being thought a fool, than to talk and remove all doubt of it." - 1907, Maurice Switzer
|
|
|
01-16-2015, 02:03 PM
|
#7
|
Senior Member
Join Date: Jun 2014
Location: Box Elder, South Dakota
Trailer: Bigfoot 25' 2018
Posts: 347
|
Tim & Julie: That would be great, I'll PM you.
IceBreaker: It's not the table trim. I need the C or U channel which goes over the 1/8" plywood at the top of the dinette seat. I've Googled and found similar molding, mostly for auto use, but not close enough. I think it's a rigid plastic but haven't yet pulled the old stuff off.
I also thought I needed the molding for the front dinette panel. This is around the angled piece at the front of the dinette between the trailer wall and floor. It's also 1/8" ply but has a different flexible molding. I was able to re-use the original here.
This is picture of the front corner of the dinette. I've built up the dinette height so ignore the lumber.
I hope this makes sense.
Thanks.
__________________
Hugh Currin
2018 Bigfoot 25'
2018 RAM 2500 Diesel
|
|
|
01-16-2015, 02:33 PM
|
#8
|
Senior Member
Join Date: Apr 2012
Location: Edmonton, Alberta
Trailer: 2013 19' & 2013 15B
Posts: 2,636
|
Quote:
Originally Posted by currinh
Tim & Julie: That would be great, I'll PM you.
IceBreaker: It's not the table trim. I need the C or U channel which goes over the 1/8" plywood at the top of the dinette seat. I've Googled and found similar molding, mostly for auto use, but not close enough. I think it's a rigid plastic but haven't yet pulled the old stuff off.
I also thought I needed the molding for the front dinette panel. This is around the angled piece at the front of the dinette between the trailer wall and floor. It's also 1/8" ply but has a different flexible molding. I was able to re-use the original here.
This is picture of the front corner of the dinette. I've built up the dinette height so ignore the lumber.
I hope this makes sense.
Thanks.
|
Sorry, I thought you were looking for the plastic table trim. The "oak" (or similar) trim must be available at locations other than Chilliwack. But of course, if Reace can send you a piece, that would save you the trouble of sourcing it yourself.
__________________
2013 19' \ 2013 15B, 2020 Toyota 4Runner TRD Offroad
"It is better to remain silent at the risk of being thought a fool, than to talk and remove all doubt of it." - 1907, Maurice Switzer
|
|
|
01-16-2015, 06:10 PM
|
#9
|
Senior Member
Join Date: Jan 2014
Location: North Van., British Columbia
Trailer: 2014 Escape 19, sold; 2019 Escape 21, Sept. 2019
Posts: 8,786
|
Quote:
Originally Posted by currinh
I need the C or U channel which goes over the 1/8" plywood at the top of the dinette seat. I've Googled and found similar molding, mostly for auto use, but not close enough. I think it's a rigid plastic but haven't yet pulled the old stuff off..
|
I've looked in a couple of places that had similar products but the color didn't match. I'll keep looking but sooner or later I'll be passing by ETI and if I haven't found any by then I'll buy some from them.
Ron
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|