|
08-13-2015, 05:23 PM
|
#1
|
Senior Member
Join Date: Mar 2015
Location: Austin, Texas
Trailer: 2009 Escape 19'
Posts: 242
|
Springfield 3-Stage Pedestal Install
There is a lot of discussion about this pedestal but not much info on how to install it. I installed mine today and thought it might be helpful to document the project. I have 19’ with the standard dinette. This is by no means a "how-to", just a simple guide.
First, I took some measurements. I found that the the floor space between the front of the benches was 1 1/2” wider than the back. So the dinette floor space bows out slightly. I also observed that the original pedestal bases were offset 1” towards the driver side bench, probably to provide a little more wiggle room on the passenger side. These are just minor details that don’t really affect the install, but I wanted to center the new pedestal.
To center the pedestal, I used a T square to pencil a cross and align the base holes. I marked the holes and drilled some pilots. Then I used the supplied screws to mount the pedestal to the floor.
After mounting and collapsing the pedestal, drop the table into bed position. There should be just under 5/8” clearance between the top of the pedestal and the table slider. Align the pedestal table mount so that it is flush with the sides of the table slider. Mark the holes and drill pilots. I attached the table using the countersunk screws from the original pedestal bases, but it would be better to use flatheads.
Thats pretty much it! The table sits 2.5” from the back wall in fully raised position. I should have mounted the pedestal base a few inches from center toward the wall to compensate for this, but I don’t think it would make much of a difference. The table is very stable.
I am a little disappointed that the pedestal doesn’t seem to have enough power to raise the table on its own. It needs a little help. Does anyone else with a full size table have this problem?
|
|
|
08-13-2015, 05:25 PM
|
#2
|
Senior Member
Join Date: Mar 2015
Location: Austin, Texas
Trailer: 2009 Escape 19'
Posts: 242
|
A few more pics...
|
|
|
08-13-2015, 05:38 PM
|
#3
|
Senior Member
Join Date: Feb 2013
Location: Solvang, California
Trailer: 2016 21' Escape (usetaowna a 19, a Burro and 2 Casitas)
Posts: 842
|
Very nice. Where'd you get the pedestal?
Greg
|
|
|
08-13-2015, 05:47 PM
|
#4
|
Senior Member
Join Date: Mar 2015
Location: Austin, Texas
Trailer: 2009 Escape 19'
Posts: 242
|
Overtons. Now is a good time to buy with 20% off!
|
|
|
08-13-2015, 06:08 PM
|
#5
|
Senior Member
Join Date: Jan 2014
Location: North Van., British Columbia
Trailer: 2014 Escape 19, sold; 2019 Escape 21, Sept. 2019
Posts: 8,809
|
That's a great price. Good work on figuring out how to deal with the non-parallel space. Probably better to have that little bit of clearance. Would have been a nuisance to had ended up with a close fit that allowed the table edge to rub on the vinyl.
I've got a feeling that those pedestals are going to be more and more popular as people find out about them (and how horrible the standard one is) to the point that they become an option.
Ron
|
|
|
08-13-2015, 06:14 PM
|
#6
|
Senior Member
Join Date: Jun 2013
Location: Felton, California
Trailer: 2018 21' ; 2014 19' (Sold)
Posts: 1,309
|
Great tutorial. Thank you!
__________________
Jan
We do not remember days, we remember moments.
- Cesare Pavese
|
|
|
08-13-2015, 06:32 PM
|
#7
|
Senior Member
Join Date: Oct 2012
Location: Bellingham and Glacier, Washington
Trailer: 2013 Escape 15A
Posts: 2,053
|
Quote:
Originally Posted by Ron in BC
...(and how horrible the standard one is)...
|
I have absolutely no issues whatsoever with the standard double-pedestal ETI table.
__________________
Karen Hulford
2013 Escape 15A, "Egbert"
'93 Ford 150 XLT or
'22 GMC Acadia Denali
|
|
|
08-13-2015, 07:21 PM
|
#8
|
Site Team
Join Date: Jun 2014
Location: Canyon Lake, Texas
Trailer: 2015 19 "Past Tents", 2021 F150 Lariat 2.7L EB
Posts: 10,222
|
Looks good Sean. We love ours. With the smaller table due to the U-shaped Dinette, the pedestal doesn't need any assistance lifting it, but perhaps yours does because the table is larger/heavier.
__________________
"You can't buy happiness, but you can buy an RV. And that is pretty close."
|
|
|
08-13-2015, 09:59 PM
|
#9
|
Senior Member
Join Date: Jan 2014
Location: North Van., British Columbia
Trailer: 2014 Escape 19, sold; 2019 Escape 21, Sept. 2019
Posts: 8,809
|
Quote:
Originally Posted by KarenH
I have absolutely no issues whatsoever with the standard double-pedestal ETI table.
|
Well, maybe horrible as well as beauty is in the eye of the beholder.
I've had a table support similar to the type ETI uses but, by comparison, the tapers were machined, fit well and it was rock solid. The first time I sat in an ETI demo unit, put my elbows on the table (yeah, must have been raised in a barn ) and the table tilted noticeably, I thought, well that would have been a coffee spill for sure.
Throw in the two pedestals taking up valuable foot room, more difficult to use than an easy up and down single pedestal and I do wonder why ETI doesn't upgrade their offerings.
Ron
|
|
|
08-14-2015, 04:46 AM
|
#10
|
Senior Member
Join Date: Sep 2009
Location: Southwick, Massachusetts
Trailer: None, sold my 2014 5.0TA
Posts: 7,124
|
If I seat the dual pedestal table with enough force it doesn't wobble much. If I don't use enough force it's all over the place. Same as the table in the Starcraft, so it's no big deal, pretty much used to it. However the 3 stage is on the list for next spring.
__________________
Happy Motoring
Bob
|
|
|
08-14-2015, 05:08 AM
|
#11
|
Senior Member
Join Date: May 2012
Location: Halifax, Nova Scotia
Trailer: 2014 5TA/ *012 17B (previous)
Posts: 442
|
How did you fix the holes in the vinyl?
__________________
Min D
Chapi II
--------------------
'Have No Regrets'
|
|
|
08-14-2015, 10:17 AM
|
#12
|
Senior Member
Join Date: Aug 2012
Location: N/A, Indiana
Trailer: Escape
Posts: 976
|
Quote:
Originally Posted by KarenH
I have absolutely no issues whatsoever with the standard double-pedestal ETI table.
|
The issues and fixes posted in this thread are related to an escape 19 with a table that is very difficult to raise and lower with the oe pedestal system.. It is heavy and akward to manipulate. The probability of injury to the owner, floor,vinyl wall, and cabinets is high. Maybe not so with the 15A.
__________________
"Never argue with an idiot. They only bring you down to their level and beat you with experience." George Carlin
|
|
|
08-14-2015, 10:29 AM
|
#13
|
Senior Member
Join Date: May 2010
Location: Missoula, Montana
Trailer: Escape 19, 2018: Last Best Escape
Posts: 395
|
Quote:
Originally Posted by Chapitre
How did you fix the holes in the vinyl?
|
When I installed a pedestal in our 17, I used a colored caulk from Ace. Seemed to work and provided a nice waterproof seal.
Klaus
__________________
2018 Escape 19: Last Best Escape
2015 Escape 19 (previous): Escape Goats
2011 Escape 17 (previous): SittEscape
Honda Pilot 2019
|
|
|
08-14-2015, 10:55 AM
|
#14
|
Senior Member
Join Date: Oct 2012
Location: Bellingham and Glacier, Washington
Trailer: 2013 Escape 15A
Posts: 2,053
|
Quote:
Originally Posted by Jubal
The issues and fixes posted in this thread are related to an escape 19 with a table that is very difficult to raise and lower with the oe pedestal system.. It is heavy and akward to manipulate. The probability of injury to the owner, floor,vinyl wall, and cabinets is high. Maybe not so with the 15A.
|
I was referring to the larger 4-person table in my 15 which I believe is of a similar (if not the exact same) size as that in the 19. I don't use it as a bed so don't have to fight putting it up and down, but other people seem to manage that very well. I do not think it is a horrible table and simply didn't want newbies to think they now have to spend a lot of money on a different table system. I don't have a problem with it being too wobbly but then I get up from the table using my own legs, not the table for support.
Edited: If I did have to make up a bed on a daily basis, I would have ordered the other table which is held by a cleat to the wall and then lowered to the bed position on hinges.
__________________
Karen Hulford
2013 Escape 15A, "Egbert"
'93 Ford 150 XLT or
'22 GMC Acadia Denali
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|