|
|
05-16-2016, 09:40 AM
|
#1
|
Junior Member
Join Date: Nov 2014
Location: Nanaimo, British Columbia
Trailer: 2015 - 5.0TA
Posts: 3
|
Fan in breaker box
Trying to find information about the fan in the breaker box and how long it should stay running? When we first headed out on vacation it would run for a couple of minutes when plugged into power then shut off . Now it has run for 1/2 hour and still running batteries are fully charged according to the panel.
|
|
|
05-16-2016, 09:45 AM
|
#2
|
Site Team
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 11,051
|
Are you sure it's not in the inverter?
__________________
Donna D.
Ten Forward
2014 Escape 5.0TA
|
|
|
05-16-2016, 09:49 AM
|
#3
|
Senior Member
Join Date: Aug 2012
Location: N/A, Indiana
Trailer: Escape
Posts: 976
|
Quote:
Originally Posted by Donna D.
Are you sure it's not in the inverter?
|
The inverter fan would not run unless it is being used to convert 12V to 120V. The inverter is not in the electrical distribution box.
The converter in the bottom of the electrical distribution box has a fan that could run as 120V is being converted to 12V and is plugged into a campground 120V outlet.
__________________
"Never argue with an idiot. They only bring you down to their level and beat you with experience." George Carlin
|
|
|
05-16-2016, 09:59 AM
|
#4
|
Junior Member
Join Date: Nov 2014
Location: Nanaimo, British Columbia
Trailer: 2015 - 5.0TA
Posts: 3
|
It's the fan in the electrical panel box. We are plugged in to shore power and have the battery switch on.
|
|
|
05-16-2016, 11:08 AM
|
#5
|
Senior Member
Join Date: Nov 2008
Location: Southern Alberta, Alberta
Trailer: 2015 Escape 5.0TA
Posts: 1,734
|
I believe its temperature controlled. Ours has run for extended periods when we have plugged into shore power. Sorry just can't remember how long but it was awhile. It is the converter in the fuse box. I would be more concerned if it never ran. Hope this helps.
Cheers
Doug
__________________
Cheers
Doug
|
|
|
05-16-2016, 11:20 AM
|
#6
|
Junior Member
Join Date: Nov 2014
Location: Nanaimo, British Columbia
Trailer: 2015 - 5.0TA
Posts: 3
|
Quote:
Originally Posted by PGDriver
I believe its temperature controlled. Ours has run for extended periods when we have plugged into shore power. Sorry just can't remember how long but it was awhile. It is the converter in the fuse box. I would be more concerned if it never ran. Hope this helps.
Cheers
Doug
|
Hi this does help as we couldn't find any info if it should keep running. When we were plugged in at home it would run for a short period then cut out and the same at the last campsite.
|
|
|
05-16-2016, 11:34 AM
|
#7
|
Site Team
Join Date: Jun 2014
Location: Canyon Lake, Texas
Trailer: 2015 19 "Past Tents", 2021 F150 Lariat 2.7L EB
Posts: 10,222
|
Doug's right. It comes on as needed based on a temperature sensor.
Sent from my iPhone using Tapatalk
__________________
"You can't buy happiness, but you can buy an RV. And that is pretty close."
|
|
|
05-16-2016, 04:52 PM
|
#8
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
I have an electrical panel question. I understand the unit houses 12vdc fuses and 120 vac breakers. It also houses the converter as well as the charger.
Is it a simple operation to disable the charger? I have my own and do not plan on utilizing the built in one. I did this on an older American brand one.
__________________
Santiago
|
|
|
05-16-2016, 05:10 PM
|
#9
|
Senior Member
Join Date: Jan 2014
Location: North Van., British Columbia
Trailer: 2014 Escape 19, sold; 2019 Escape 21, Sept. 2019
Posts: 8,812
|
Really easy. Power to it comes from the same breaker that powers the microwave.
You can follow the black wire from the converter up to #1 circuit breaker.
Ron
|
|
|
05-16-2016, 05:14 PM
|
#10
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
Thank you Ron, yes a lot easier that the one I modified.
By the way, will Escape include a whole trailer wiring diagram when we pick up our trailer later this year ? Part of the factory documentation ?
__________________
Santiago
|
|
|
05-16-2016, 05:21 PM
|
#11
|
Senior Member
Join Date: Sep 2009
Location: Southwick, Massachusetts
Trailer: None, sold my 2014 5.0TA
Posts: 7,124
|
Not that I've heard of. I certainly didn't get one.
__________________
Happy Motoring
Bob
|
|
|
05-16-2016, 05:36 PM
|
#12
|
Senior Member
Join Date: Oct 2012
Location: Bellingham and Glacier, Washington
Trailer: 2013 Escape 15A
Posts: 2,055
|
Quote:
Originally Posted by Santiago
By the way, will Escape include a whole trailer wiring diagram when we pick up our trailer later this year ? Part of the factory documentation ?
|
This has been discussed in at least two other threads:
http://www.escapeforum.org/forums/f9/wiring-7535.html
http://www.escapeforum.org/forums/f3...atic-3698.html
The short answer is "no" for several legitimate (in my opinion) reasons.
__________________
Karen Hulford
2013 Escape 15A, "Egbert"
'93 Ford 150 XLT or
'22 GMC Acadia Denali
|
|
|
05-16-2016, 07:15 PM
|
#13
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by Santiago
I have an electrical panel question.
...
It also houses the converter as well as the charger.
|
Just for clarification: the converter is the charger; there are not two separate devices.
You should be able to remove the converter/charger module entirely - leaving the distribution panel and cabinet intact - if you don't want to haul around the deadweight. Personally, I would just put a switch in the supply circuit and leave it in place: that way, it would be available as a backup to your preferred charger, and if the plan changes it could be used without any additional work. If there is a spare circuit breaker slot, the converter/charger supply could be moved to a separate breaker, which could be left off to disable the converter/charger.
|
|
|
05-16-2016, 08:12 PM
|
#14
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
Quote:
Originally Posted by Brian B-P
Just for clarification: the converter is the charger; there are not two separate devices..
|
Brian, you mean that the when on shore power the converter is supplying house load AND what's left of its capacity is used to charge the batteries, assuming they are in need of charge.
__________________
Santiago
|
|
|
05-16-2016, 09:02 PM
|
#15
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by Santiago
Brian, you mean that the when on shore power the converter is supplying house load AND what's left of its capacity is used to charge the batteries, assuming they are in need of charge.
|
Yes.
The converter/charger runs at the voltage it thinks is needed for battery charging, not the constant (and usually lower) voltage which would be ideal for powering all of the "12 volt" DC stuff in the trailer (the house loads). It has 55 amps output capacity; when you're using a few amps for other things, there's still lots of capacity left to charge the battery. This way the battery is never disconnected from the house loads when in use (although there is a battery disconnect switch for storage).
|
|
|
05-16-2016, 09:22 PM
|
#16
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
Quote:
Originally Posted by Brian B-P
Yes.
The converter/charger runs at the voltage it thinks is needed for battery charging, not the constant (and usually lower) voltage which would be ideal for powering all of the "12 volt" DC stuff in the trailer (the house loads). It has 55 amps output capacity; when you're using a few amps for other things, there's still lots of capacity left to charge the battery. This way the battery is never disconnected from the house loads when in use (although there is a battery disconnect switch for storage).
|
Well I know most all individual converters and some inverters double up as a charger but I thought a panel assembly would have a constant dc supply for house needs (converter) and a separate charger with fluctuating voltages that will produce higher voltages when charging. I wonder if the occasional higher voltage stage supplied to the house would harm less robust 12vdc items. My inverter will not have charging and now I see that even when in a panel the converter is still acting like a charger. When I disconnect the Escape's converter within the panel using just the batteries and my 10 year old Xantrax TrueCharge 40 charger that will be the sole house supply while on shore power. I wonder if I can automatically isolate the converter to supply the house and not charge when shore power is sensed?
__________________
Santiago
|
|
|
05-16-2016, 10:18 PM
|
#17
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
I think I have my solution Brian, I can keep the converter intact and it will act as a dc supply to the house but not touch my battery banks when 120 vac power is applied from the power bush ( as Glenn calls it ).
Using a $15 elctromechanical relay with 120vac coil, SPDT 40 amp DC contacts.
That will divert DC to the house from either the converter when 120vac is present or the batteries when no 120vac is available. While tapped to onshore power the TrueCharge charger will still charge the batteries at full speed unbeknownst on the house side due to the relay acting as a DC traffic cop. Even though this relay is rated at 1million cycles I will carry a spare. Does that make sense ?
__________________
Santiago
|
|
|
05-17-2016, 12:23 AM
|
#18
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by Santiago
Well I know most all individual converters and some inverters double up as a charger but I thought a panel assembly would have a constant dc supply for house needs (converter) and a separate charger with fluctuating voltages that will produce higher voltages when charging.
|
I haven't seen that yet, although high-priced RVs could have anything. All of the recent integrated distribution panels with converters that I've heard of in small trailers have a single converter which is also used as the charger. My 2002 large fifth-wheel trailer came with a separate constant-voltage converter and the battery was always connected, so that converter was the charger. My 2010 motorhome has the same arrangement, but with a modern multi-stage converter/charger.
Quote:
Originally Posted by Santiago
I wonder if the occasional higher voltage stage supplied to the house would harm less robust 12vdc items.
|
Although I haven't seen anything damaged, the higher voltage put out by the Progressive Dynamics converter/charger in my motorhome is certainly too high for the furnace: the fan runs too loudly and just doesn't sound right. Lights visibly brighten.
I have considered a voltage regulator, to provide constant voltage to the house loads, but not seriously pursued it yet.
Quote:
Originally Posted by Santiago
I wonder if I can automatically isolate the converter to supply the house and not charge when shore power is sensed?
|
Quote:
Originally Posted by Santiago
I think I have my solution Brian, I can keep the converter intact and it will act as a dc supply to the house but not touch my battery banks when 120 vac power is applied from the power bush ( as Glenn calls it ).
Using a $15 elctromechanical relay with 120vac coil, SPDT 40 amp DC contacts.
That will divert DC to the house from either the converter when 120vac is present or the batteries when no 120vac is available. While tapped to onshore power the TrueCharge charger will still charge the batteries at full speed unbeknownst on the house side due to the relay acting as a DC traffic cop. Even though this relay is rated at 1million cycles I will carry a spare. Does that make sense ?
|
You only really need SPST, to disconnect the battery from the house loads when on AC power; the converter can always be connected to the distribution panel and the charger can always be connected to the battery, since neither does anything when there is no AC power. This is how my 1979 Boler is set up. An AC powered relay (integrated with the converter and distribution panel) disconnects the battery from the DC distribution panel, so the converter never connects to the battery. There is no charger in this Boler; the charger was an optional extra component, which just connected converter output to the battery until the battery was sufficiently charged. Santiago, your setup would use a relay in a similar way, but have a superior separate charger.
In this arrangement, you would need to decide which side of the relay (converter/panel or battery) connect the output of any solar charger, determining where solar output would go when on shore power.
The stock converter is a multi-stage charger. With no battery connected, it won't "know" that and - depending of what loads are in use - may not immediately go into the float mode that you would want.
|
|
|
05-17-2016, 12:36 AM
|
#19
|
Senior Member
Join Date: Jul 2015
Location: Anaheim CA, California
Trailer: SOLD 2016 Classic 21ft - SOLD 2016 Ram 1500 tug - ORDERED Van Replacement
Posts: 516
|
Quote:
Originally Posted by Brian B-P
I haven't seen that yet, although high-priced RVs could have anything. All of the recent integrated distribution panels with converters that I've heard of in small trailers have a single converter which is also used as the charger. My 2002 large fifth-wheel trailer came with a separate constant-voltage converter and the battery was always connected, so that converter was the charger. My 2010 motorhome has the same arrangement, but with a modern multi-stage converter/charger.
I have considered a voltage regulator, to provide constant voltage to the house loads, but not seriously pursued it yet.
You only really need SPST, to disconnect the battery from the house loads when on AC power; the converter can always be connected to the distribution panel and the charger can always be connected to the battery, since neither does anything when there is no AC power. This is how my 1979 Boler is set up. An AC powered relay (integrated with the converter and distribution panel) disconnects the battery from the DC distribution panel, so the converter never connects to the battery. There is no charger in this Boler; the charger was an optional extra component, which just connected converter output to the battery until the battery was sufficiently charged. Santiago, your setup would use a relay in a similar way, but have a superior separate charger.
In this arrangement, you would need to decide which side of the relay (converter/panel or battery) connect the output of any solar charger, determining where solar output would go when on shore power.
.
|
Wow, it sounds like this will work as you have done so yourself. The SPDT was to isolate the converted when no AC was available and the batteries would supply the house. I see your point of not needing it but I am paranoid and rather not let the batteries mingle with the converter. I do not plan on solar at this stage so will worry about that much later on.
Quote:
Originally Posted by Brian B-P
Although I haven't seen anything damaged, the higher voltage put out by the Progressive Dynamics converter/charger in my motorhome is certainly too high for the furnace: the fan runs too loudly and just doesn't sound right. Lights visibly brighten..
|
Brian, I suspect the lights brighten because of the high voltages cause by the converter's charger thinking its going to charge the batteries. Incandescent bulbs won't last long in that mode. Another reason for not having DC power supply and charger all in one.
Quote:
Originally Posted by Brian B-P
The stock converter is a multi-stage charger. With no battery connected, it won't "know" that and - depending of what loads are in use - may not immediately go into the float mode that you would want.
|
How the converter would behave in he absence of a battery bank, I wondered about that as well. You say i will go into float mode? Why if house load drops voltage? Only way to really tell is to temporarily isolate battery and see what the converted will do. This is when I wish the converter was not so smart with three stages, I want the old retarded ones back!
Brian, you have given me hope of having separate dedicated components based on your fairly vast RV experiences. THANK YOU.
__________________
Santiago
|
|
|
05-17-2016, 10:12 AM
|
#20
|
Senior Member
Join Date: Oct 2014
Location: Chattanooga, Tennessee
Trailer: 2015 19 foot
Posts: 439
|
Back to the original question. I have noticed lately that when the power first comes on, the fan runs - until I remember to switch the refrigerator from 12vdc to 120vac. (I run the refrigerator on 12vdc while traveling, and that works great for me.) Then the fan stops. I suspect that there is some 12vdc load causing the fan to run.
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|