|
06-23-2019, 02:11 PM
|
#1
|
Senior Member
Join Date: Aug 2018
Location: WALNUT, California
Trailer: 2019 5.0 TA The Glass Inn
Posts: 231
|
5.0 TA Television mounts
Question for 5.0 TA owners.
When we picked up our trailer in May we had not yet purchased a T.V.,
Escape did not install the T.V. mounts without the T.V.
We have the T.V. ready option in the standard spot ( right side cabinet in bed area ). We also have T.V. ready in the dinette area ( left side upper cabinet ). I bought two arms so I had the mounts to move T.V. back and forth. My question is where are the arms mounted? Are they on the edge of the wall or on the face of the wall? Any pictures would be greatly appreciated. Thanks
|
|
|
06-23-2019, 02:28 PM
|
#2
|
Member
Join Date: Apr 2017
Location: Langley, British Columbia
Trailer: 2017 5.0TA SOLD
Posts: 57
|
TV Mount
The mount supplied by Escape attaches on the edge of the wall between the bed and the closet or cupboard next to the door; at least that's where we mounted ours. Same as you, ETI would not attach the TV mount because we didn't bring the TV with us for orientation.
Its easy to attach it to the edge of that wall with the supplied screws and the TV will be viewable from the dinette or the bed. I think ETI says the maximum TV size is 22", but our 24" fits just fine and swings freely around to face forward or back.
Sorry, no picture.
|
|
|
06-23-2019, 02:28 PM
|
#3
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
The edges of the walls cabinets should have studs and that is where ETI normally mounts the tv mount. Unless you had a wall reinforced, I'd stick to the edges.
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
06-23-2019, 04:18 PM
|
#4
|
Senior Member
Join Date: Feb 2018
Location: Austin, Texas
Trailer: 2019 5.0TA "Junior", 2019 Ram 1500 5.7 Hemi
Posts: 1,600
|
Ditto what the others have said - the framing inside the edge of the bulkhead walls is substantial and works well for attaching a tv arm mounting base with large screws. Here's a photo of the TV in the stowed position, mounted on the bulkhead wall between the bedroom and cabinet next to the door. When the arm is pulled out the TV can easily be turned to face either the bed or the dinette.
We didn't get the ETI mount - after trying another one that I didn't like, I found this one that has a couple of very handy features. It has a spring loaded pin that snaps into place when the arm is all the way back against the wall and locks it there securely for travel. There's a chain hanging down that you pull to release the lock so the arm can be swung out. The swivel joints are fairly tight - just enough play that you can easily move the TV, but snug enough that it stays in whatever position you place it in with no wobble - our old bracket required tightening down knobs on the joints which was a pain every time we moved the TV.
Here's the mounting arm: https://smile.amazon.com/gp/product/...?ie=UTF8&psc=1
We have a 22" TV - but that bulkhead wall is strong enough that you could certainly mount a larger TV if desired, as long as whatever arm you use fits that size TV.
We got a 12 volt TV with built in DVD player, and have been pleasantly surprised at the picture quality and audio volume - better than we expected for an inexpensive TV: 22" Skyworth LED 12 Volt TV DVD Combo SLC2221A
__________________
David, Mary, and the cats
|
|
|
06-23-2019, 04:49 PM
|
#5
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,546
|
I had Escape install TV hookups in the loft passenger side, and at the front of the dinette upper cabinets near the fridge. I have a 24" Samsung and installed one mounting bracket on the bulkhead to the loft bed side and one on the fridge wall. The one on the fridge wall I wanted just away from the support board so sistered another chunk in when I had the fridge removed, real easy to do.
All that and we have watched the TV once in 2 1/2 years of owning as it is really only used when weather is really crappy and we are stuck inside. I am sure this will hit us in the future, it did one trip before this trailer.
We keep the RV and arm stowed except when viewing.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
05-11-2020, 10:27 PM
|
#6
|
Junior Member
Join Date: Oct 2019
Location: Madison, Wisconsin
Trailer: 2020 5.0TA
Posts: 29
|
Hello David. So the mount (and the TV when not being viewed) is facing the wardrobe? Is that what I'm seeing in your pic? Are you able open the cabinet to the right of the door? Do you find that watching the TV from the bed in the 5.0 is comfortable? Thank you so much. Your posts have been very helpful as we plan for our 5.0TA.
|
|
|
05-12-2020, 06:03 AM
|
#7
|
Senior Member
Join Date: Feb 2018
Location: Austin, Texas
Trailer: 2019 5.0TA "Junior", 2019 Ram 1500 5.7 Hemi
Posts: 1,600
|
Quote:
Originally Posted by LuGreen
Hello David. So the mount (and the TV when not being viewed) is facing the wardrobe? Is that what I'm seeing in your pic? Are you able open the cabinet to the right of the door? Do you find that watching the TV from the bed in the 5.0 is comfortable? Thank you so much. Your posts have been very helpful as we plan for our 5.0TA.
|
Yes, in the stowed position the TV is pushed back against that cabinet door with the TV facing the wardrobe. It's easy to just release the lock on the mount and pull it out a bit to access that cabinet next to the door, we normally only keep it all the way back in the locked position for travel.
We find it comfortable to watch TV from the bed, usually propped up with pillows. With the TV swung around the other direction you can see it from the dinette.
__________________
David, Mary, and the cats
|
|
|
05-12-2020, 09:26 AM
|
#8
|
Senior Member
Join Date: Jul 2014
Location: Tampa Bay Area, Florida
Trailer: 2015 Escape 5.0TA (Little Elsie) Extensively Personalized
Posts: 2,976
|
Quote:
Originally Posted by davidmurphy02
Yes, in the stowed position the TV is pushed back against that cabinet door with the TV facing the wardrobe. It's easy to just release the lock on the mount and pull it out a bit to access that cabinet next to the door, we normally only keep it all the way back in the locked position for travel.
We find it comfortable to watch TV from the bed, usually propped up with pillows. With the TV swung around the other direction you can see it from the dinette.
|
I agree with all of David’s comments. Easy to watch from bed or dinette and a slight push on the mount if it is in a position that blocks cabinet access. The only thing I would add is that I believe ETI recommends that the TV not be left in place during travel as it’s weight may put stress on the screws that attach to the stud in the wall. It is key to note that these studs are not 2 x 4s; they are somewhat flimsy. The mount ETI supplies does not lock in place using a pull chain (I did have that mount in my previous SOB trailer an it worked well) but it does separate into two pieces as the half attached to the TV can be slid up and out of the half attached to the cabinet stud. We typically transport our TV in a custom sewed sack made from a bath towel, face down in the space between the mattress and the outer wall. Our TV is a 19-inch Toshiba. A larger TV might not fit into that space but we have also transported it atop the mattress.
__________________
What a long strange trip it’s been!
|
|
|
05-12-2020, 09:47 AM
|
#9
|
Senior Member
Join Date: Feb 2018
Location: Austin, Texas
Trailer: 2019 5.0TA "Junior", 2019 Ram 1500 5.7 Hemi
Posts: 1,600
|
I don't know the dimensions of the framing lumber in the end of that bulkhead panel where the TV mounts, but it is fairly substantial and very solid - I had to predrill holes for the two large mounting screws for the TV wall bracket, and I'd guess it is 1-1/2" thick at least. I was originally dubious about leaving the TV mounted for travel, but TV's are pretty lightweight these days, and since the mount locks securely to the wall I decided to give it a try. A year later, after speed bumps and rough roads, the TV has been fine and it is certainly easier to leave it on the wall mount.
That one big bump in Capitol Reef NP didn't affect the TV, but the entire contents of our pantry dumped out on the floor. A locking latch on the pantry door has corrected that little issue.
__________________
David, Mary, and the cats
|
|
|
05-12-2020, 12:48 PM
|
#10
|
Senior Member
Join Date: Jul 2014
Location: Tampa Bay Area, Florida
Trailer: 2015 Escape 5.0TA (Little Elsie) Extensively Personalized
Posts: 2,976
|
Quote:
Originally Posted by davidmurphy02
I was originally dubious about leaving the TV mounted for travel, but TV's are pretty lightweight these days, and since the mount locks securely to the wall I decided to give it a try. A year later, after speed bumps and rough roads, the TV has been fine and it is certainly easier to leave it on the wall mount.
That one big bump in Capitol Reef NP didn't affect the TV, but the entire contents of our pantry dumped out on the floor. A locking latch on the pantry door has corrected that little issue.
|
David, not my intention to contradict you or suggest you that you are going to have problems. I would love to switch to the chain locking bracket and leave the TV in place 24/7/365. As I stated, I installed that same bracket in a previous SOB (Shoddily Constructed And Maintenance Plagued) trailer. That particular company installs veneered plywood walls in their Deluxe models. I was able to mount the bracket with bolts using fender washers on the back side of a cabinet wall.
I am just repeating what I was told by ETI during orientation when they installed the bracket. If ETI has ceased recommending that a TV can be left in place while towing I would change brackets In a heartbeat and leave the TV in place as you do.
Perhaps others who have recently picked up and had the TV bracket installed can comment what ETI now recommends?
__________________
What a long strange trip it’s been!
|
|
|
05-12-2020, 12:57 PM
|
#11
|
Senior Member
Join Date: Feb 2018
Location: Austin, Texas
Trailer: 2019 5.0TA "Junior", 2019 Ram 1500 5.7 Hemi
Posts: 1,600
|
Quote:
Originally Posted by C&G in FL
David, not my intention to contradict you or suggest you that you are going to have problems. I would love to switch to the chain locking bracket and leave the TV in place 24/7/365.
|
Hey, no worries, I didn't take it that way at all - the more opinions the better - at least here on the forum! Just relating my experience. I also previously had a much more flimsy stick and tin trailer, and have been impressed at how very solid everything is throughout the Escape. At the Pineknot rally last fall I showed David Desjardins a few things in our trailer, including the TV bracket, and he was taking notes for possible product upgrade discussions later...don't know whether anything ever came of that as far as the TV bracket. They are always tweaking and improving things, though, glad to see that they replaced the battery disconnect switch with a more robust switch and also moved it inside the dinette bench where it will never get turned off by mistake.
__________________
David, Mary, and the cats
|
|
|
05-14-2020, 02:46 PM
|
#12
|
Junior Member
Join Date: Oct 2019
Location: Madison, Wisconsin
Trailer: 2020 5.0TA
Posts: 29
|
Quote:
Originally Posted by davidmurphy02
Yes, in the stowed position the TV is pushed back against that cabinet door with the TV facing the wardrobe. It's easy to just release the lock on the mount and pull it out a bit to access that cabinet next to the door, we normally only keep it all the way back in the locked position for travel.
We find it comfortable to watch TV from the bed, usually propped up with pillows. With the TV swung around the other direction you can see it from the dinette.
|
Thank you for the pics! I understand now....
|
|
|
05-14-2020, 05:04 PM
|
#13
|
Senior Member
Join Date: Jul 2018
Location: Minneapolis, Minnesota
Trailer: 2019 5.0 TA
Posts: 864
|
Quote:
Originally Posted by davidmurphy02
Ditto what the others have said - the framing inside the edge of the bulkhead walls is substantial and works well for attaching a tv arm mounting base with large screws. Here's a photo of the TV in the stowed position, mounted on the bulkhead wall between the bedroom and cabinet next to the door. When the arm is pulled out the TV can easily be turned to face either the bed or the dinette.
We didn't get the ETI mount - after trying another one that I didn't like, I found this one that has a couple of very handy features. It has a spring loaded pin that snaps into place when the arm is all the way back against the wall and locks it there securely for travel. There's a chain hanging down that you pull to release the lock so the arm can be swung out. The swivel joints are fairly tight - just enough play that you can easily move the TV, but snug enough that it stays in whatever position you place it in with no wobble - our old bracket required tightening down knobs on the joints which was a pain every time we moved the TV.
Here's the mounting arm: https://smile.amazon.com/gp/product/...?ie=UTF8&psc=1
|
We originally planned on mounting our television as David did, but we found placing the television on the counter worked well for us and we won't need to move it to get into the cupboards. We don't and likely won't be watching watch television in bed. We store it laying flat above the microwave cabinet along with a laptop and some of Colleen's computer needs. We could just as well set it beside the bed if we wanted that space for something else.
We did add the TV/cable ready with 120V option, but we have been using a MIFI Hotspot from Verizon which works out well for us.
If anyone is interested I have the same mounting arm as David, it is $40.95 on Amazon, I'd sell it for $20 plus shipping. It is unused in it's original box. https://smile.amazon.com/gp/product/...?ie=UTF8&psc=1
__________________
The Sweet Suite
Ronn and Colleen
|
|
|
05-15-2020, 08:36 AM
|
#14
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,546
|
I installed a RV mount on the front door side in the loft, and one in the driver front side of the dinette. Easy to do. We actually used the one in the dinette once, but not the one in the loft, in the 3 years of having this setup. TV for us is really not used much as there are other things we prefer to do. Though there was one trip to Oregon that saw storming weather for two weeks straight 4 years back that saw us watch a bit more.
Our TV gets stowed away when not in use or when travelling. This is easy to do, gets it right out of the way, causes no stress on bumpy roads, and looks way better too.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|