I decided to change from the standard table setup to a Lagun table in our new 2023 E19 that we bought without U-shaped dinette.
This involves building a new wall for the Lagun table mount. I opted to build this from 3/4" maple plywood.
I removed the front maple-colored large piece of trim that is attached to the front of the trailer, between the benches. This creates a "cable tunnel" between the two benches. I also removed the piece of wood screwed into the floor that served as a place to fasten that large piece of trim, since this would be in the way for the wall.
I also had to remove the trim pieces near the floor on both benches, as well as the wood slats that the bed rests on, and that is mounted to the side of the benches, up near the top.
Once those were removed, I cut a piece of the maple plywood to fit in between the two benches. I made it tall enough that with a "lid" of 3/4" plywood, it would be flush with the slats that the table rests on in bed mode, so that the space could still be used as a bed when needed.
The vertical wall is attached to the floor with seven L-brackets, and sits as far back as possible without covering any of the power outlets or electrical equipment. In this position, a few more L-brackets can be screwed through the sides of the benches and into the bench framing, and all L-brackets will be hidden behind the wall.
I then put back the slats that the table rests on when in bed-mode. I had to cut these to now fit tight against the wall, and screwed them back into the bench framing as it was previously mounted.
If you think about the vertical wall that the Lagun table is mounted to, it will tend to pivot "backwards" into the trailer near the top, and "forward", towards the front wall of the trailer near the bottom. The way I cut the slats, the top of the wall is sitting up against the slats, so in addition to the L-brackets, the entire slat (which is screwed into the bench framing) holds the wall in place in the critical direction -- and this is why I added as many as seven brackets into the floor.
I also put some left-over pieces of wood behind the vertical wall, against the sides of the benches, again screwed into the framing. This now acts as support for the "lid" (see below).
After this, the vertical wall is fully in place, and strong enough for use. However, the 3/4" thick plywood still flexes when I pulled hard on the Lagun system (simulating someone leaning on the table, or even just the weight of the table).
The top of the box is therefore also built out of strong 3/4" maple plywood, that is screwed into the vertical wall with 2" screws, as well as in to the top of the slats extending in behind the wall. This way, this lid sits in a position where the table now rests on it when in bed mode, and the lid acts as a super strong reinforcement of the vertical wall, so with this screwed in place, there is no longer any flex in the wall.
If I ever want to get into the "box" for accessing the cables or anything else, I'll have to unscrew the lid. Maybe I'll add a little door or something at some point, if I can figure out where to do that without compromising strength.
After all this, I added the trim back on the sides of the benches down by the floor, and added another piece of trim at the bottom near the floor on the new vertical wall too, in order to make it look the same.
This involves building a new wall for the Lagun table mount. I opted to build this from 3/4" maple plywood.
I removed the front maple-colored large piece of trim that is attached to the front of the trailer, between the benches. This creates a "cable tunnel" between the two benches. I also removed the piece of wood screwed into the floor that served as a place to fasten that large piece of trim, since this would be in the way for the wall.
I also had to remove the trim pieces near the floor on both benches, as well as the wood slats that the bed rests on, and that is mounted to the side of the benches, up near the top.
Once those were removed, I cut a piece of the maple plywood to fit in between the two benches. I made it tall enough that with a "lid" of 3/4" plywood, it would be flush with the slats that the table rests on in bed mode, so that the space could still be used as a bed when needed.
The vertical wall is attached to the floor with seven L-brackets, and sits as far back as possible without covering any of the power outlets or electrical equipment. In this position, a few more L-brackets can be screwed through the sides of the benches and into the bench framing, and all L-brackets will be hidden behind the wall.
I then put back the slats that the table rests on when in bed-mode. I had to cut these to now fit tight against the wall, and screwed them back into the bench framing as it was previously mounted.
If you think about the vertical wall that the Lagun table is mounted to, it will tend to pivot "backwards" into the trailer near the top, and "forward", towards the front wall of the trailer near the bottom. The way I cut the slats, the top of the wall is sitting up against the slats, so in addition to the L-brackets, the entire slat (which is screwed into the bench framing) holds the wall in place in the critical direction -- and this is why I added as many as seven brackets into the floor.
I also put some left-over pieces of wood behind the vertical wall, against the sides of the benches, again screwed into the framing. This now acts as support for the "lid" (see below).
After this, the vertical wall is fully in place, and strong enough for use. However, the 3/4" thick plywood still flexes when I pulled hard on the Lagun system (simulating someone leaning on the table, or even just the weight of the table).
The top of the box is therefore also built out of strong 3/4" maple plywood, that is screwed into the vertical wall with 2" screws, as well as in to the top of the slats extending in behind the wall. This way, this lid sits in a position where the table now rests on it when in bed mode, and the lid acts as a super strong reinforcement of the vertical wall, so with this screwed in place, there is no longer any flex in the wall.
If I ever want to get into the "box" for accessing the cables or anything else, I'll have to unscrew the lid. Maybe I'll add a little door or something at some point, if I can figure out where to do that without compromising strength.
After all this, I added the trim back on the sides of the benches down by the floor, and added another piece of trim at the bottom near the floor on the new vertical wall too, in order to make it look the same.
Attachments
Last edited:
