|
|
11-23-2013, 04:49 PM
|
#41
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,552
|
Quote:
Originally Posted by fudge_brownie
With the scissors jack I used a 18 volt cordless drill with the same 3/4 socket. It made quick work. With the stabilizer jack will I want to do the same thing?
|
Yes you will, same size.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
11-23-2013, 04:50 PM
|
#42
|
Member
Join Date: May 2013
Location: Flower Mound, Texas
Trailer: 21' Escape
Posts: 87
|
Under the features section on the 21 it states that it has front and rear scissor stabilizer jacks. They may not be heavy enough to actually lift the trailer
|
|
|
11-23-2013, 04:54 PM
|
#43
|
Senior Member
Join Date: Oct 2009
Location: Galesville, Wisconsin
Trailer: 2017 21 "Blue II" & 2017 Highlander XLE (previously 2010 17B "Blue" & 2008 Tacoma)
Posts: 4,234
|
Quote:
Originally Posted by floorpanel
Under the features section on the 21 it states that it has front and rear scissor stabilizer jacks. They may not be heavy enough to actually lift the trailer
|
I think both types can use the scissor name due to the way they open and close- confusing. And probably based on their capacity and the weight of the trailer/RV, both could in some instances be stabilizing only... more confusion.
__________________
Eric (and Mary who is in no way responsible for anything stupid I post)
"Beware of false knowledge; it is more dangerous than ignorance." George Bernard Shaw
|
|
|
11-23-2013, 05:20 PM
|
#44
|
Senior Member
Join Date: Feb 2010
Location: Marysville, Washington
Trailer: 2022 Coachmen Nova 20C
Posts: 652
|
They look like the ones in thoer's post (40) to me....
__________________
Paul & Norma
2013 Escape 21 & 2014 Chevy Silverado - sold
2022 Coachmen Nova 20C
|
|
|
11-23-2013, 05:26 PM
|
#45
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
There maybe an issue with your torsion suspension if you try to level your trailer side to side with scissors jacks, raising the trailer but not the suspension to a point where the trailer may be level but the wheels and torsion axle on high side are fully compressed whereas the wheels/axle on the low side are fully extended. Using wheel levelers would not cause this issue. Just a thought.
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
11-23-2013, 05:40 PM
|
#46
|
Senior Member
Join Date: Oct 2009
Location: Galesville, Wisconsin
Trailer: 2017 21 "Blue II" & 2017 Highlander XLE (previously 2010 17B "Blue" & 2008 Tacoma)
Posts: 4,234
|
Quote:
Originally Posted by cpaharley2008
There maybe an issue with your torsion suspension if you try to level your trailer side to side with scissors jacks, raising the trailer but not the suspension to a point where the trailer may be level but the wheels and torsion axle on high side are fully compressed whereas the wheels/axle on the low side are fully extended. Using wheel levelers would not cause this issue. Just a thought.
|
Jim - I always use all 4 to some degree, so I don't think that should be the case as even on the low side there is at least some lifting with the Jack. Does that make sense? And if it is really far off I use my Legos! LOL
__________________
Eric (and Mary who is in no way responsible for anything stupid I post)
"Beware of false knowledge; it is more dangerous than ignorance." George Bernard Shaw
|
|
|
11-23-2013, 05:55 PM
|
#47
|
Senior Member
Join Date: Nov 2008
Location: Janesville, WI, Wisconsin
Trailer: Escape 19 (sold) Escape 21 2014
Posts: 1,884
|
Paul W
From your picture I am assuming we are seeing a frame for a new 21? That rear stabilizer is close to the axle. Glad I will be sleeping in the front, there could be quite some movement in the rear of the trailer.
Eric
We were close to delivery dates on our trailers and I believe you were also given the scissors as original equipment. Even if they do hang lower they are a substantial jack. I liked them. At the same time they were probably over the top in what they needed to do. When I replaced the lost jack (somewhere in nighttime Nebraska) I tried to find what brand they were. All the labels had been removed, there was not a name showing anywhere. I did get a 24 inch replacement that fit fine, it just had different thread pattern and it takes for ever to raise and lower. No brand name on the replacement either.
Paul B
__________________
Paul and Janet Braun
2003 Toyota 4Runner V8 now 2012 Toyota Sequoia V8
Escape 19' 2010 now 2014 Escape 21'
|
|
|
11-23-2013, 06:00 PM
|
#48
|
Senior Member
Join Date: Oct 2009
Location: Galesville, Wisconsin
Trailer: 2017 21 "Blue II" & 2017 Highlander XLE (previously 2010 17B "Blue" & 2008 Tacoma)
Posts: 4,234
|
With that rear overhang way past the stabilizer, it might give real credence to the "If the trailer is a rockin', don't come a knockin'" stickers I have seen.....
__________________
Eric (and Mary who is in no way responsible for anything stupid I post)
"Beware of false knowledge; it is more dangerous than ignorance." George Bernard Shaw
|
|
|
11-23-2013, 08:39 PM
|
#49
|
Senior Member
Join Date: Feb 2010
Location: Marysville, Washington
Trailer: 2022 Coachmen Nova 20C
Posts: 652
|
Quote:
Originally Posted by fudge_brownie
Paul W
From your picture I am assuming we are seeing a frame for a new 21? That rear stabilizer is close to the axle. Glad I will be sleeping in the front, there could be quite some movement in the rear of the trailer.
Paul B
|
I suppose that depends on how much you weigh & what you're doing in the dinette - that's the only thing behind the rear stabs. I doubt Norma, the Girls & I will be picking up the front 3/4s of the trailer much.
The frame pic is the one Reace posted as the first 21s were being built. Current production might be different if he experienced too much wobble on this trip in one last summer.
__________________
Paul & Norma
2013 Escape 21 & 2014 Chevy Silverado - sold
2022 Coachmen Nova 20C
|
|
|
11-23-2013, 08:57 PM
|
#50
|
Site Team
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 11,051
|
I borrowed Dave&Kathie's camping picture. You can see where the BAL levers are mounted based on the orange legos in this picture. There were a bunch of us in the trailer at one time during their open house and I don't remember it being the least bit bouncy.
|
|
|
11-24-2013, 08:20 AM
|
#51
|
Senior Member
Join Date: Nov 2010
Location: Tucson, AZ, Arizona
Trailer: gone, 19 and 21 & 17B with 5.0 now. gone
Posts: 790
|
andersen camping leveler
During our two week trip home in the 21 we used the stabilizers and the bal chocks between the wheels and had no shaking at all. We would at times not un-hook and use just the rear stabilizers, one chock and the tongue jack and that just about eliminated all movement.
We are now about finished with the details and ready to go somewhere soon. The additional filter is under the sink, the satellite radio is hooked up, the new smaller size tandem wheel covers from CW fit perfectly and I don't need to install four separate ones now and all of the pictures and misc. is hanging on the walls to make it ours, we are ready to go. Maybe even to Texas in the spring and/or BC before OR.
Jack and Nancy of Tucson
|
|
|
11-24-2013, 11:14 AM
|
#52
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by barry
Going from a 17B to a 5.0 "Classic" I found the 5.0 a lot easier to level because of the independent front power jacks. Putting the front drivers side up will make the rear passenger side dip down and vice versa.
|
The front jacks are well forward of the axle, so tilting the trailer this way is also twisting it - I wouldn't do it without also pushing up on the high side with a jack behind the axle. When you twist a car this way - jacking up just one front corner - you can often feel that the doors don't fit properly until it is put back down, and car structures are stiffer than trailers.
|
|
|
11-24-2013, 11:54 AM
|
#53
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by floorpanel
Under the features section on the 21 it states that it has front and rear scissor stabilizer jacks. They may not be heavy enough to actually lift the trailer
|
That's what the web page says, but other discussions suggest that Escape only briefly used scissor jacks, and normally uses single-leg jacks. I just saw the whole lineup and the factory, and I thought I saw single-leg jacks on the 21, not scissors.
The issue isn't really the strength of the jack structure - even the lightest single-leg BAL Light Trailer Stabilizer can handle half a ton of load each. The problem is that the screw, nut, and thrust bearing of a stabilizing jack (single-leg or scissor) are not designed to be turned under full load (so that model can only lift 700 pounds); only a lifting jack is designed for that. The BAL "T" Type is similar (but bigger). I installed BAL Light Trailer Stabilizers under my current trailer (similar to an Escape 17) and the nut and thrust bearing parts are vastly inferior to the corresponding parts on any scissors jack I've seen for lifting a car to change a tire.
BAL "C" Jacks are good for lifting, but don't come in a lightweight model. I don't know if that is what Escape is installing, but if it is I woud have no issue lifting with them. The jacks in the earlier frame photo, and my vague memory of what I saw at the factory, do look like "C" jacks... if they are BAL.
|
|
|
11-24-2013, 12:02 PM
|
#54
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by thoer
With that rear overhang way past the stabilizer, it might give real credence to the "If the trailer is a rockin', don't come a knockin'" stickers I have seen.....
|
But having the stabilizers close to the suspension is better for preventing suspension bounce. When I added stabilizers (to a non-Escape trailer similar to an Escape 17), I placed then as close to the axle as practical structurally.
|
|
|
11-24-2013, 12:11 PM
|
#55
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
Quote:
Originally Posted by cpaharley2008
There maybe an issue with your torsion suspension if you try to level your trailer side to side with scissors jacks, raising the trailer but not the suspension to a point where the trailer may be level but the wheels and torsion axle on high side are fully compressed whereas the wheels/axle on the low side are fully extended. Using wheel levelers would not cause this issue. Just a thought.
|
Good to think about potential issues but I don't see any suspension concerns. The two sides of the Torflex system are completely independent in action so it does't matter if they are compressed different amounts.
Quote:
Originally Posted by thoer
Jim - I always use all 4 to some degree, so I don't think that should be the case as even on the low side there is at least some lifting with the Jack. Does that make sense? And if it is really far off I use my Legos! LOL
|
I agree with Eric. The suspension on the low side doesn't get compressed any more than just sitting on level ground with no jacks. Extending the suspension is certainly harmless to it.
The only concern I see is for the frame if too much load is taken off the axle to jacks further out toward the ends of the frame... and as Eric said, blocks are used if that much difference (which is only a couple of inches) is needed.
|
|
|
11-24-2013, 01:50 PM
|
#56
|
Senior Member
Join Date: Aug 2011
Location: St. Paul, Minnesota
Trailer: 2014 Escape 21 -- The Skylark. Towed by a 2014 Highlander
Posts: 1,159
|
When we got our 17b, I asked if we could get the Scissor jacks. We had seen Eric and Mary's Trailer, and Eric was quite positive about the benefits of the scissor jacks. But Reace talked us out of them saying they were overkill for our trailer, and when Dave did our orientation he emphasized the importance of not using the stabilizers to level the trailer -- not because they couldn't support the trailer, but because of concerns about twisting the frame.
|
|
|
11-24-2013, 02:06 PM
|
#57
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,552
|
Bottom line is, why level the trailer at all with any kind of stabilizer, when it is really easy to do so with other types of blocking under the wheels?
We have the trailer levelled side-to-side in less than two minutes, usually quicker, and we tend to camp on lots of uneven spots, not the nice close to level ones found in campgrounds.
Letting the axles take the weight only makes sense to me, most of the support will come from them, and the stabilizers just.....well, stabilize.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
11-24-2013, 03:04 PM
|
#58
|
Senior Member
Join Date: Oct 2009
Location: Galesville, Wisconsin
Trailer: 2017 21 "Blue II" & 2017 Highlander XLE (previously 2010 17B "Blue" & 2008 Tacoma)
Posts: 4,234
|
It is much safer to go with the standard stabilizers and follow closely all advice from Reace and his employees, I withdraw any and all suggestions about getting the more heavy duty ones. (It is probably wise to just stop reading here)
I don't want to draw this out, nor be didactic and by no means do I want to counter what Reace or Dave say, but I have a bit of trouble with the frame twisting idea. Given the resilience of the steel tubing the frame is made of I would think it would take much more than the few inches of adjustment that I do with the scissors jack to twist the frame. If the frame were very easily twisted then one improperly placed jack used to change a tire should cause far more twisting force than I am ever putting on it in leveling at 5 jack points.
If I were to use one jack alone and jack that corner up and leave it that way for months in storage I could see how those long term forces could cause twisting. But with all five jacks applied slowly and using them only for the few inches of fine tuning I do, I can't see how it could apply much twisting force. Even using the standard stabilizers is placing some twisting pressure on the frame, as they have to be tight enough to take some of the trailer weight or else they won't stabilize anything. Unless you are using a torque wrench to make sure each stabilizer is at exactly the same force.
__________________
Eric (and Mary who is in no way responsible for anything stupid I post)
"Beware of false knowledge; it is more dangerous than ignorance." George Bernard Shaw
|
|
|
11-24-2013, 05:01 PM
|
#59
|
Senior Member
Join Date: Dec 2012
Location: Edmonton, Alberta
Trailer: 1979 Boler B1700
Posts: 14,935
|
I understand what you're saying, Eric. I think it may help to keep in mind that most well-designed instructions correctly assume that most users will not be careful or understand what they are doing.
|
|
|
11-24-2013, 05:04 PM
|
#60
|
Senior Member
Join Date: Oct 2012
Location: Longview, WA, Washington
Trailer: 2013 Escape 15B - 2014 Nissan Frontier SL
Posts: 854
|
Re:
With that rear overhang way past the stabilizer, it might give real credence to the "If the trailer is a rockin', don't come a knockin'" stickers I have seen.....
__________________
Eric (and Mary who is in no way responsible for anything stupid I post)
We have found that the smaller the trailer and the lighter the mass that it is very easy to move the trailer even if we aren't doing much. The stabilizers on the 15 are BAL "C" and I added pads and these bars made by BAL. They lift when the stabilizers are taken up. They work great although I may have to adjust them as the mounting bracket may interfere with a jack when needed.
__________________
Tim and Julie
2013 Escape 15B
2014 Nissan Frontier, Previous 2012 Santa Fe
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|