Wheel bearing repacking

[canoeman]

We have an Escape 21 with a little over 5,000 miles on it. This Spring we will get a Spring service on it before we put about another 2,000 miles on it. When should I have the wheel bearing cleaned and repacked??

[Perry Butler]

Originally Posted by canoeman

We have an Escape 21 with a little over 5,000 miles on it. This Spring we will get a Spring service on it before we put about another 2,000 miles on it. When should I have the wheel bearing cleaned and repacked??

We put 10-15,000 miles driving our camper(s) down the road. Every fall I have the bearings repacked, and brakes inspected/adjusted. At 7,000 miles a year you should be able to go two years before servicing your bearings.

Enjoy,

Perry

[SageRpod]

I had always heard the guidance and 1 year or 10,000 miles. I'm sure your trailer will not turn into a pumpkin if you go over a tad.

[Randy in Maine]

I agree that 15,000 miles or about every 2 years is OK to drive before the wheel bearing need repacking. Unless:

1) the tires are wearing unevenly or just on the inside or the outside edges, or
2) when jacked up you can get some sort of rocking or wobbling when you push/pull on the wheel at either the 3&6 o'clock or 6&12 o'clock positions, or
3) the trailer brakes are awkward or erratic or need to be looked at anyway.

It is not big money ~ $50 or a real high skill operation to repack the wheel bearings. I can do all 4 of mine in a day or so with just some new seals and fresh wheel bearing grease. I have owned a few VW busses over the years and I had to do it on them also.

[SageRpod]

Originally Posted by Randy in Maine

...2) when jacked up you can get some sort of rocking or wobbling when you push/pull on the wheel at either the 3&6 o'clock or 6&12 o'clock positions, ...

I prefer 3:15 and 5:45 so I can call it a day 30 minutes early

(Thank you, the late great George Carlin for that one)

[Kingfish]

Does grease age out with low mileage?

[HABBERDABBER]

Originally Posted by Kingfish

Does grease age out with low mileage?

I don't think so, in a normal lifetime. It's just another hydrocarbon concoction.

Given decades or millenia, it may not last.

Nothing is forever, and nothing lasts.

Forever.

[MrLynn]

Last summer, before our aborted trip to the Pennsylvania Wilds, I greased the wheel bearings using the EZ-lube feature. My understanding is that if you do that once a year or so, you don't need to pull off wheels and repack bearings.

[Rossue]

Originally Posted by MrLynn

Last summer, before our aborted trip to the Pennsylvania Wilds, I greased the wheel bearings using the EZ-lube feature. My understanding is that if you do that once a year or so, you don't need to pull off wheels and repack bearings.

If it were me having bought a used trailer I would treat it like buying a used car and err on the side of caution. There is a whole thread on EZ lube or not, however your trailer is now 4-5 years old and I would want to do a full bearing and brake inspection.

[C&G in FL]

Originally Posted by Kingfish

Does grease age out with low mileage?

Grease does not necessarily “age out.” Grease is essentially oil in a carrier agent. But grease can separate (oil separation from the carrier), especially if stored in hot locations. Peanut butter can be used as an analogy. Have you ever seen a small puddle of oil in the “nooks and crannies” of the peanut butter after it has set for a while? Or have you ever found parts of your grease gun oil covered?

Originally Posted by MrLynn

Last summer, before our aborted trip to the Pennsylvania Wilds, I greased the wheel bearings using the EZ-lube feature. My understanding is that if you do that once a year or so, you don't need to pull off wheels and repack bearings.

MrLynn, I would respectfully say that you are badly mistaken in your understanding. In as much as the so-called EZ-lube feature could be considered an “interim” bearing maintenance method, this feature pushes old grease from the inner bearing through the outer bearing until “clean” grease appears and the method can displace the rear seal contaminating brake surfaces if not done with care. My analogy for that is like spraying a dirty dish in the sink. It may look clean, but do you want to eat your next meal on it? Bearings and races should be examined for wear periodically and brakes can be examined at the same time. Last I knew, unless it has been endowed with AI, the EZ-lube feature lacks optical abilities.

[C&G in FL]

Honestly, I will go 2 years or 25,000 miles, have done that for many years and have never had a wheel bearing problem. I usually do clean and pack them myself, and there was no unusual wear on the bearings or races when I last serviced them. I use Lucas Red “N” Tacky which doesn’t seem to separate as much as some of the other greases I have used in the past. The brakes get adjusted every 6,000 to 8,000 miles.

[CharlesinGA]

Buy good seals. National Seal 473336 Has a spring loaded double lip and will replace the Dexter 010-019-00 that is used on 3000 to 4400 lb axles. 1.719 inside dia, and 2.565 OD

Charles

[HABBERDABBER]

I've posted this info before, and it might help someone.
On my 2016 "classic" vintage E19, the inner grease seals were glued in. I damaged the bearings on the first wheel I was working on and replaced the races and bearings, trying to remove the grease seal. I had to use heat on the brake drum to overcome the adhesive.
First time I've seen them glued in. I have done tear downs and re-greasing before on boat and other travel trailers before. I don't know if Dexter still glues them in.
I believe they glue them in place to avoid pop-out from overzealous greasing with the EZ Lube feature. I didn't use glue on the inner seals when I performed my repack.

[brroberts]

I agree with Habberdabber. I didn’t use heat as the bearing was going to be toast. Instructions recommended adhesive on the replacement. I did not since I am careful and typically do lube by tear down so I can inspect things.

[Iowa Dave]

We have Easy Lube axles on our 2013 21. When we got it I disassembled the hubs, examined the brakes, and repacked the bearings. When I cleaned up the spindles it gave me a chance to closely examine how that feature works and to put some new clean grease in the easy lube voids, driving out the old grease. Then I cleaned everything up and reassembled with hand packed new grease. Then I did this again in 2018, 2019 and 2020 because we traveled a lot in those first three years. Since then with Covid I’ve grease every 8,000 to 11,000 miles. I’ve posted several times that I feel the examination gives me Peace of mind and I’m working on the trailer anyway rotating the tires, cleaning things up and checking the other systems so to me it’s just what I do.

I bought my first boat trailer when I was 15, got the wheel bearing lesson from my dad who was a European Theatre tanker in WWII and never looked back except to back in, and then not that often after I mastered the mirrors. I buy grease and parts from Midwest Wheel in Cedar Rapids, Iowa. Smart people on the counter, genuine Dexter dealers and speedy service. YMMV
Iowa Dave

[ghosthunter]

We purchased a 2013 15 B in spring of 2021. It was current on maintenance than. I used the EZ lube feature each year since. But we are driving less than 5 k a year.

I have it scheduled in two weeks for break inspections and wheel bearing service.
$150.00 per axle for bearing service.

I don’t care to mess with it.

[HABBERDABBER]

Wise enough decision.
It's knuckle scraping, grease monkey grunt work. A chore for the driveway mechanic, rough on the back, hands,... heck, the body.
I do mine, as it is an infrequent task, and I forget how much ache it creates.
That, and the fact that I am retired and enjoy a super-abundance of time, the sort of which is not money, and I have 2 axles on the E19, lead me to my misspent dotage.
Who does the deed doesn't matter. What matters is that the deed gets done.

[Chowdagirl]

Hello all. I have a 2020 E19. I noticed my passenger side front tire is wearing on the inside. The tires are fairly new. I have to admit but I have never had the brakes inspected . I have only done local Florida trips. I want to take it to a shop because we are doing a 3 month trip out west starting in March. In reading the forum it sounds Iike the bearings need to be repacked. I had heard that they should not overpack them. Need some Escapee advice! Thank you!!!

[HABBERDABBER]

Ask around for a good shop to do your brake inspection and repacking. There are shops that specialize in service for trailers and that can be one venue. Folks have complaints about the big box RV service shops, but it ALL depends on the experience and good service of the person doing the work. Local independent garage mechanics can do excellent work.
Ask around.
And consider replacing that tire.
This type of service ain't rocket science. There should be plenty of shops able to do a good job.
Research it too. Dexter has online info and you can provide a shop with a copy of their service procedures and specifications.

And have a swell trip out West.