|
|
11-08-2012, 09:16 AM
|
#1
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
Hot Water Heater Anode Question...
Hello all,
Can anyone comment on how long the HWH anode usually lasts?
Mine is 1 1/2 years old and looking pretty swiss cheesey
I have never used the HWH (we just buy showers at the campgrounds). I'm thinking of putting a bypass in.
Also, a coworker with an airstream says I should get a plastic HWH plug but I was dubious. Anyone have any experience with those?
Thanks,
Glenn
2012 Honda Pilot
2011 Escape 19'
2006 Irish Terrier
|
|
|
11-08-2012, 09:30 AM
|
#2
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
You already have a bypass installed in your Escape by the factory, located under the bed, 2 plastic valves located behind the water heater, if you close them then you will by pass your water heater. If you by pass then you will not need to worry about the anode rod. The anode rod is sacrificial in that it corrodes in lieu of your water tank. If no water, no rust. You can't use the plastic plug with the anode rod, if not in use, you can use the plastic. The rods can lasts for years, depends on your water.
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
11-08-2012, 09:44 AM
|
#3
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,559
|
Yep, just bypass like Jim said with the factory installed valves. The anode needs to be pretty much down to the rod in the middle before it needs to be replaced. Mine has been used for 4 years and has at least another one left.
I would not use a plastic plug and lose the corrosion protection, whether I used it or not.
We very rarely use our shower too, but the hot water is nice to have for body and dish washing though, and usually turn ours on in the morning for an hour or so, and then again at suppertime.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
11-08-2012, 09:45 AM
|
#4
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
Great! I'll switch it off now while the system is empty for winter.
Good to see another Escape 19 from PA. They were scarce in the East when I was considering buying mine.
Thanks,
Glenn
2012 Honda Pilot
2011 Escape 19'
2006 Irish Terrier
|
|
|
11-08-2012, 11:59 AM
|
#5
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
Where are you in relation to York, Pa? Are you on the map, yet?
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
11-08-2012, 01:25 PM
|
#6
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
I am in Southwestern PA, due west of you.
I don't appear to be on the map. Do I have to do anything or does it just happen soon after joining?
BTW, does PA require inspections on the Escape 19? I was told no because it is under a weight limit but found it hard to believe.
Glenn
2012 Honda Pilot
2011 Escape 19'
2006 Irish Terrier
|
|
|
11-08-2012, 02:44 PM
|
#7
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,559
|
Glenn, click on the link at the bottom of the map to go right to the Google Maps page. There are instructions there on how to place your marker.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
11-08-2012, 03:48 PM
|
#8
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
Ahh, I think I got it now. I should show up after Google's confirmation.
Thanks,
Glenn
|
|
|
11-08-2012, 03:57 PM
|
#9
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
And there I am! :-)
|
|
|
11-08-2012, 06:05 PM
|
#10
|
Senior Member
Join Date: Oct 2008
Location: Calgary, Alberta
Trailer: 2017 Escape 5.0 TA
Posts: 15,559
|
You must be the Myers then.
__________________
2017 Escape 5.0 TA
2015 Ford F150 Lariat 3.5L EcoBoost
2009 Escape 19 (previous)
“Most folks are about as happy as they make up their minds to be.” — Abraham Lincoln
|
|
|
11-08-2012, 10:10 PM
|
#11
|
Junior Member
Join Date: May 2012
Posts: 21
|
Arathar, Irish Terriers rock.
|
|
|
11-09-2012, 08:53 AM
|
#12
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
Indeed, they do.
|
|
|
11-09-2012, 08:54 AM
|
#13
|
Member
Join Date: Nov 2012
Location: Canonsburg, Pennsylvania
Trailer: 2011 Escape 19'
Posts: 31
|
Yep, that's me.
|
|
|
09-28-2013, 10:16 PM
|
#14
|
Member
Join Date: Jul 2011
Location: Laramie, Wyoming
Trailer: 2011 19' Escape
Posts: 49
|
Here is a guide to replacing your anode.
__________________
2009 Chevy Silverado
2011 19' Escape
|
|
|
09-29-2013, 07:08 AM
|
#15
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
great info, thanks....
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
09-29-2013, 07:25 AM
|
#16
|
Senior Member
Join Date: Oct 2008
Location: St. Thomas not BVI., Ontario
Trailer: 2014 Escape 5.0TA / 2016 Ram Eco Diesel 4X4
Posts: 8,038
|
Hi: 182king... Just finished cleaning the anode rod and flushing the water heater yesterday. The rod isn't far off 0% so I put some new teflon tape on it and will put it back in today. Thanks for the insight. I didn't think it was to bad!!! Alf
escape artist N.S. of Lake Erie
__________________
Quote Bugs Bunny..."Don't take life too seriously, none of us get out of it ALIVE"!!!
'16 Ram Eco D. 4X4 Laramie Longhorn CC & '14 Escape 5.0TA
St.Thomas (Not the Virgin Islands) Ontario
|
|
|
09-29-2013, 07:53 AM
|
#17
|
Site Team
Join Date: Nov 2008
Location: Portland, Oregon
Trailer: 2014 Escape 5.0 TA
Posts: 11,064
|
Does the hotwater heater come from the factory with a by-pass for winterizing? Or does this need to be an owner mod?
|
|
|
09-29-2013, 08:15 AM
|
#18
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
factory by pass is installed by Escape, but you may want to ask reace to install the E-Z winterizing valve that lets your pump suck in your antifreeze conveniently.
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
09-29-2013, 08:46 AM
|
#19
|
Senior Member
Join Date: Sep 2012
Location: Ottawa, Ontario
Trailer: 2013 Escape 19
Posts: 743
|
I bought a winterizing valve and found it wouldn't fit in the space I had -- it was intended to screw directly onto the pump, but the pump was situated with the input right close to the wheel well -- no space to insert the T fitting.
If you're adding the winterizing valve yourself, make sure you've got room for whatever you purchase.
__________________
Doug
2013 Escape 19 ("The Dog House") , 2018 Ford F150
|
|
|
09-29-2013, 09:25 AM
|
#20
|
Senior Member
Join Date: Jun 2010
Location: Central, Pennsylvania
Trailer: Escape#5 2022 E19
Posts: 26,268
|
Doug, you may have to move the pump anyway if it doesn't have flexible hoses which eliminate a lot of noise while in operation. Several member with 19's have already moved and installed the flexible hoses and some even went with the reserve mini tank accumulator that cuts on/off by almost 50%. I guess what I'm saying, once you get started there are a lot of options available.
Here is one thread http://www.escapeforum.org/forums/f8...pump-1592.html
__________________
Jim
Sometime life gets in the way of living.......
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|